Reconfigurable Robot Enables University of Toronto Students to Study Realistic Industrial Robots
- Students prepared for work in industry
- Complex optimizations automated
- Months of development time eliminated
“With MATLAB and Simulink we developed a low-cost design and simulation environment that enables students to apply theoretical aspects of kinematics, dynamics, and controls of robot manipulators in a realistic way, optimize their designs, and see those designs in action.”Dr. Reza Emami, University of Toronto
Because of budget constraints, most university robotics labs can provide at best one type of basic robot. As a result, students have little hands-on experience in the design of robots and their control systems, and very limited access to robot manipulators commonly used in industry.
To address these limitations, the University of Toronto Institute for Aerospace Studies developed a reconfigurable robot manipulator and an Integrated Design and Simulation Environment (IDSE). Built using MATLAB® and Simulink®, the robot and IDSE enable students to design, simulate, optimize, and operate most configurations of robot manipulators used in industry today.
“With Simulink and Simulink 3D Animation, students can visualize a realistic simulation of the robot,” says Dr. Reza Emami, senior lecturer at the University of Toronto Institute for Aerospace Studies. “Using the IDSE, the students can identify the best configuration of kinematic, dynamic, and control parameters for a given task before testing their design on an actual robot manipulator.”
Dr. Emami and his team of students and engineers used MATLAB and Simulink to model the reconfigurable robot and to build the IDSE.
They generated a Simulink and Simscape Multibody™ model of the robot by importing an XML representation of its CAD assembly using Simscape Multibody Link, and then added blocks for the actuators and other electronic components from Simscape Electrical™. They modeled the driver circuits for motors and solenoids using Simscape Electrical™ transistor blocks. They used Simscape™ to integrate the mechanical and electrical subsystems in the model.
Using Simulink 3D Animation™, the group created an animated 3D representation from the model that enables students to visualize the robot in a virtual reality environment.
Working in MATLAB and Simulink, Dr. Emami and his colleagues developed the IDSE user interface and additional modules that the students need to complete course assignments.
The optimization module, implemented with Simulink Control Design™ and Simulink Design Optimization™, enables students to configure the robot for a specific trajectory or task by identifying an optimal set of dynamic, kinematic, and control parameters.
For course assignments, students use MATLAB and Control System Toolbox™ to create plots and visualize system behavior in the time and frequency domains, as well as to calculate proportional, derivative, and integral gains for each joint in a selected configuration.
The students use the IDSE to complete their design, simulation, and optimization exercises and to visualize the 3D animation of the robot. Ultimately, once they have verified their design through simulations, the students will test them on the actual robot.
Students prepared for work in industry. “Our students now have a reconfigurable platform that enables them to explore the various robot configurations they are likely to encounter in the industry,” says Dr. Emami. “They are learning to design optimized robots for a given task, which would be impossible if they were working with only one type of robot manipulator with a fixed configuration.”
Complex optimizations automated. “Our robot has 18 degrees of freedom in total, and I was initially skeptical about the ability of software optimization tools to handle such a complex problem,” says Dr. Emami. “We found that Simulink Control Design and Simulink Design Optimization work well with such complex, realistic systems, something I have not seen with other tools.”
Months of development time eliminated. “The ability to translate our CAD assemblies into a Simscape Multibody model saved us months of development time,” says Dr. Emami. “The resulting model provided the basis for the core simulation and visualization features in our design environment.”
University of Toronto is among the 1300 universities worldwide that provide campus-wide access to MATLAB and Simulink. With the Campus-Wide License, researchers, faculty, and students have access to a common configuration of products, at the latest release level, for use anywhere—in the classroom, at home, in the lab or in the field.
Berichten Sie über Ihre erfolgreichen Projekte
Treten Sie dem Customer Reference Programm bei