NXP FRDM-KL25Z Microcontroller Support from Simulink Coder
Use Simulink and Simulink Coder to program your FRDM-KL25Z microcontroller with the TFC-SHIELD to connect servos, motors, and cameras.
- NXP FRDM-K64F Support from Simulink Coder
- NXP FRDM-KL25Z Microcontroller Support from Simulink Coder
Explore gallery (4 images)
The Simulink Coder Support Package for NXP™ FRDM-KL25Z Board includes automated build and execution, processor-optimized code for ARM® Cortex-M, block libraries for on-chip and on-board peripherals, and deployment support using a built-in scheduler.
The supported peripherals for this board are:
- 14 digital input/outputs
- 6 analog inputs
- 1 analog output
- 3 serial Tx/Rx from three on-board UARTs
- RGB LED
Additionally, this support package provides a library of blocks to interface with the TFC-SHIELD (purchased separately from the main board). The supported peripherals, when using this shield, include:
- 2 line scan cameras
- 1 on-board dipswitch
- 2 on-board potentiometers
- 2 on-board push buttons
- 2 servos
- 2 DC motors
The following three examples will help you get started:
- Getting Started with Freescale FRDM-KL25Z Support Package
- Code Verification and Validation with External Mode
- Servo Control
Simulink Coder hardware support packages offer built-in, limited, support for specific hardware, schedulers, and compilers. Please click the Request Hardware Support link if you seek additional hardware support.
Platform and Release Support
See the hardware support package system requirements table for current and prior version, release, and platform availability.
View enhancements and bug fixes in release notes.
Related Hardware Support Views: ARM, Control Systems, C ∕ C++ Code Generation, Embedded Systems, Freescale, MathWorks Supported, NXP, Power Electronics Control Design, Project-Based Learning, Simulink Coder, Simulink Product Family, Support Package Installer Enabled
Ready to install?
Before installing the support package, confirm you have the correct setup. View system requirements and installation options.
Get support packageCheck the System Requirements
To install a hardware support package, you must have a supported product release, along with the required operating system and base product.
View the hardware support package system requirements table and confirm you have:
- A supported release
- A supported operating system
- The required base products
If you do not have a supported release or the required base products, you can get started with a free trial, or you can purchase products.
Continue with the Installation
After confirming you have the system requirements, proceed with either installation option listed below.
Option 1: Using the Toolstrip
Launch the Support Package Installer from your version of MATLAB and navigate to the correct support package.
Option 2: "Get Support Package" Button (.mlpkginstall file*)
Clicking the Get Support Package button provides the support package install file:
([filename].mlpkginstall)
There are several ways to initiate the Support Package Installer from these files:
- Open the
.mlpkginstallfile directly from your Internet browser. - Download and save the file (the default option for some Internet browsers), and open it directly from your Windows, Mac, or Linux operating system.
- Open the
.mlpkginstallfile directly from within MATLAB by navigating the Current Folder to the location of the downloaded file and double clicking it. That will initiate the installation for the MATLAB release that you have open.
The primary difference between using the .mlpkginstall file (option 2) rather than the toolstrip (option 1) to initiate support package installation is that the file allows the user to avoid the support package selection screen on the installer.
*These file types were introduced in MATLAB R2013a.
Users without an Internet connection can install hardware support packages by following the download instructions.
Software
Required
Recommended
- Control System Toolbox
- DSP System Toolbox
- Signal Processing Toolbox
- Simulink Control Design
- Stateflow
Support Package
Required
Support Package Installer installs this support package and all required third-party software. To start the installer, go to the MATLAB toolstrip and click Add-Ons > Get Hardware Support Packages.
Hardware
Required
- FRDM-KL25Z
- USB mini Cable
Recommended
- TFC-SHIELD
- TFC-CAMERA-ASY
- TFC-KIT (includes the above)
Software
Required
Don't see the hardware you're looking for?
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
Select web siteYou can also select a web site from the following list:
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)