Community Profile

photo

J Chen


Last seen: 6 Tage ago Active since 2019

Statistics

All
  • 36 Month Streak
  • Thankful Level 2
  • Knowledgeable Level 4
  • 5-Star Galaxy Level 1
  • Personal Best Downloads Level 2
  • Revival Level 2
  • GitHub Submissions Level 3
  • Thankful Level 1
  • First Review
  • First Submission
  • First Answer

View badges

Content Feed

View by

Answered
(Simscape multibody) Is there any way to use a specific angle as a input for revolute joint?
Set the Actuation tab as follows: Torque - Automatically computed, Motion - Provided by Input. You also need Simulink-PS Convert...

14 Tage ago | 0

Answered
Generic Engine stalling when load applied
You need to specify an initial speed for the propeller. It is done in the Variables tab of the Propeller Inertia block.

16 Tage ago | 0

Answered
Simscape Results Explorer not showing entire simulation data
Select Model Settings tab. Click Simscape. Uncheck "Limit data points" box.

16 Tage ago | 0

| accepted

Answered
Can I read voltage and current measurement from simulink model that containts a model of connections in Arduino Uno?
Use the Analog Input block froo the Simulink Support Package for Arduino.

16 Tage ago | 0

| accepted

Answered
Simscape vehicle body incline angle
Connect a Simulink signal source block through a Simulink-PS Converter block (in Simscape-Utilities) to the beta port.

etwa 2 Monate ago | 0

Answered
How to measure output torque of a gear in simscape multibody?
Choose the Total Torque in the Composite Force/Torque Sensing tab.

3 Monate ago | 0

Answered
How to visualize movement that occurred by reaction force with Simscape multibody?
The grey cube should move if it is not fixed and connected to the arm through a revolute joint. The motion maybe too small for y...

3 Monate ago | 0

Answered
Cannot find "body" block on Simscape
No sure what is the Body block in R2017. You can find Mass and Inertia blocks in the Simscape Foundation Library - Mechanical - ...

3 Monate ago | 0

| accepted

Question


PID Tuner couldn't find a stabilizing controller
The PID block in the attached Simulink file stabilizes the plant (the plant is defined in the call back). However, the PID Tuner...

3 Monate ago | 0 answers | 0

0

answers

Answered
How to rotate an image in Matlab
You basically read the image into a matrix, then change the array element to a different location (swich row to column, etc.)

4 Monate ago | 0

Answered
Clock on Mechanics Explorer Video
A simple solution is to do a screen recording that includes the Time display at the bottom of the Mechanics Explorer. Powerpoint...

4 Monate ago | 0

Answered
Automaticly change of actuation of joints in Simscape multibody.
Use name = gcb to get block names (select a block first) Use get_param(name,'DialogParameters') to get parameter names. The par...

4 Monate ago | 1

| accepted

Answered
Finding natural frequency and mode shape of damped 4 degree of freedom
Use F=ma to develop the differntial equations for m1, m2. Use F=ma and M=Iw for m3. The natural frequencies and mode shapes are ...

4 Monate ago | 0

Answered
Design a Transmission Shift Controller
Use a MATLAB Function block in SImulink. You can put the logic in the block. Persist variables could be useful (link).

5 Monate ago | 0

Answered
How do i add a drive cycle in simscape to a genric engine.
You need a controller that compare the desired and measured speeds to generate the throttle command. This is not a trivial task....

5 Monate ago | 0

Answered
How to find pressure at every section of pipes in series in simscape? One end of pipe is connected to a constant pressure source and another end is open to the atmosphere
Use the Hydraulic Pressure Sensor block in the Simscape Fundation Library - Hydraulic.

5 Monate ago | 0

Answered
G ports in simulink?
To get the G port: open the Spherical Solid block. Expand the Export under the Geometry and check the Entire Geometry box.

5 Monate ago | 0

| accepted

Answered
Multiple Joints on flexible parts in Simscape Multibody
You can add new frames to the body elements. The new frames will have new associated ports. You can apply the forces at these po...

5 Monate ago | 0

Answered
Is it a reliable number when pid tuning is performed using simscape multibody?
The Simulink PID block correctly implement a PID control. You specify the gains in the block dialog box.

5 Monate ago | 0

Answered
Moment of inertia with coordinates
Moment of inertia is or , where m is the mass, r is the distance to the rotation axis.

5 Monate ago | 0

Answered
Is there another way to increase the mass flow rate on simscape?
You need to understand the physics. Flow rate and pressure are related. The pressure in a volume is determined by in and out flo...

6 Monate ago | 0

| accepted

Answered
How to draw a Motor efficiency map having speed, torque and efficiency?
Use contour(x,y,z), where x, y need to be in grid corrdinate. You can study the following example for the grid coordinate x = 1...

6 Monate ago | 0

Answered
Combining Simscape-Simulink Matlab versions 2018 and 2021
Replace the hard stop block with the hard stop block in the 2021a Simulink Library Browser.

7 Monate ago | 0

| accepted

Answered
Connection between current measurement and sum block
Use a PS-Simulink Converter block https://www.mathworks.com/help/physmod/simscape/ref/pssimulinkconverter.html#:~:text=The%20PS%...

7 Monate ago | 0

Answered
Simscape Multibody, Transform Sensor, quaternion output
Take a look at this: https://www.mathworks.com/matlabcentral/answers/415936-angle-between-2-quaternions

8 Monate ago | 0

Answered
Would it be possible to change the greyscale to a blue scale?
Take a look at the colormap command - https://www.mathworks.com/help/matlab/ref/colormap.html

8 Monate ago | 0

Answered
The following code is not giving errors, but it does not solve the system of equations.
In order to solve a system of equations, the number of equations needs to equal the number of variables. You also need ==0 for t...

8 Monate ago | 0

Answered
Solving a system of three second order coupled differential equation
Use as states and express the derivatives of the states as functions of the states, e.g., d/dt()=etc.

9 Monate ago | 0

Answered
Solving ODE with sqrt
If you know how to solve an ODE in Matab, the problem might be negative values for the sqrt().

11 Monate ago | 0

Answered
how to get eigenvalues and plot it
Use a loop to calculate and store the eigenvalues for each time point. Plot the data outside the loop.

11 Monate ago | 0

| accepted

Load more