photo

준호


Last seen: 6 Tage vor Aktiv seit 2023

Followers: 0   Following: 0

Statistik

  • Thankful Level 1

Abzeichen anzeigen

Feeds

Anzeigen nach

Frage


How to implement an LQR controller when the system's state variables and control inputs have different units?
Hello, I am wondering how to implement an LQR controller when the state variables and control inputs have different units. For...

9 Tage vor | 1 Antwort | 0

1

Antwort

Frage


How to implement MPC when the number of states is greater than the number of outputs?
I want to implement MPC using MATLAB's Model Predictive Control Toolbox. When I checked the official MATLAB website, I found on...

10 Tage vor | 1 Antwort | 0

1

Antwort

Beantwortet
How to troubleshoot pixhawk build error problem during executing example file?
Hello, I have another problem, that is QGroundControl doesn't recognize a pixhawk board when px4 firmware was built from MATL...

16 Tage vor | 0

Beantwortet
How to troubleshoot pixhawk build error problem during executing example file?
I just fixed this problem by installing PX4-Autopilot firmware to the Linux home directory(not windows directory) and not execut...

etwa ein Monat vor | 1

Frage


How to troubleshoot pixhawk build error problem during executing example file?
Hello, I want to execute the example of Send and Receive Serial Data Using PX4 Autopilots Support Package. I followed the step...

etwa ein Monat vor | 2 Antworten | 0

2

Antworten

Frage


How can I execute a Simulink block only when a specific condition is met?
Hi all, Is there a way to execute the following block diagram only when a certain condition is satisfied (e.g., when a joysti...

3 Monate vor | 1 Antwort | 0

1

Antwort

Frage


How to use "StabilityThreshold" estimation option in greyest function?
Hello, To predict the lateral equations of the H4 Hercules using a greybox model, I defined the model function as follows and s...

4 Monate vor | 1 Antwort | 0

1

Antwort

Frage


Problem Occurred While Using MATLAB System Identification Toolbox
Hello, I am currently performing system identification using the System Identification Toolbox after extracting the response dat...

4 Monate vor | 1 Antwort | 0

1

Antwort

Frage


Inquiry about IP address and port number for UDP Send and UDP Receive block
Hello all, I have a question about the IP addresses and port numbers for the UDP Send and UDP Receive blocks. When sending and ...

5 Monate vor | 1 Antwort | 0

1

Antwort

Frage


How to store object(like udp object) in level-2 s-function?
Hello all, I want to send control input from Matlab to FlightGear and receive aircraft data from FlightGear to Matlab with UDP ...

7 Monate vor | 1 Antwort | 0

1

Antwort

Frage


How to calculate minimum singular value of I+L and I+inv(L) for MIMO system?
Hello, I want to calculate minimum singular value for MIMO system, and here is an example %% A = [0.1873 0.8403 -0.6003 -2.1...

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


What's the difference between two command?
Hello, In general, the command of nyquist plot is nyquist(sys,omega), but an example of textbook the command of nyquist is nyqu...

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


How to maintain eigenvalues sequence
Hello, I have to draw root-locus for longitudinal motion; Short Period Mode and Phugoid Mode. Here is a code %% Dynamics Vp =...

etwa ein Jahr vor | 0 Antworten | 0

0

Antworten