준호

Last seen: 4 Monate vor | Aktiv seit 2023

Followers: 0 Following: 0

Statistik

All

Feeds

Frage

How do I use Simulink Coder to build a Simulink model and generate the necessary header files that seem to be missing?
Hello, I’m trying to build a simple LQR block diagram using Simulink Coder for deployment on a Raspberry Pi board. However, du...

10 Monate vor | 1 Antwort | 0

1

Antwort

Frage

How to implement an LQR controller when the system's state variables and control inputs have different units?
Hello, I am wondering how to implement an LQR controller when the state variables and control inputs have different units. For...

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage

How to implement MPC when the number of states is greater than the number of outputs?
I want to implement MPC using MATLAB's Model Predictive Control Toolbox. When I checked the official MATLAB website, I found on...

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Beantwortet
How to troubleshoot pixhawk build error problem during executing example file?
Hello, I have another problem, that is QGroundControl doesn't recognize a pixhawk board when px4 firmware was built from MATL...

mehr als ein Jahr vor | 0

Beantwortet
How to troubleshoot pixhawk build error problem during executing example file?
I just fixed this problem by installing PX4-Autopilot firmware to the Linux home directory(not windows directory) and not execut...

mehr als ein Jahr vor | 1

Frage

How to troubleshoot pixhawk build error problem during executing example file?
Hello, I want to execute the example of Send and Receive Serial Data Using PX4 Autopilots Support Package. I followed the step...

mehr als ein Jahr vor | 2 Antworten | 0

2

Antworten

Frage

How can I execute a Simulink block only when a specific condition is met?
Hi all, Is there a way to execute the following block diagram only when a certain condition is satisfied (e.g., when a joysti...

mehr als ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage

How to use "StabilityThreshold" estimation option in greyest function?
Hello, To predict the lateral equations of the H4 Hercules using a greybox model, I defined the model function as follows and s...

mehr als ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage

Problem Occurred While Using MATLAB System Identification Toolbox
Hello, I am currently performing system identification using the System Identification Toolbox after extracting the response dat...

mehr als ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage

Inquiry about IP address and port number for UDP Send and UDP Receive block
Hello all, I have a question about the IP addresses and port numbers for the UDP Send and UDP Receive blocks. When sending and ...

mehr als ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage

How to store object(like udp object) in level-2 s-function?
Hello all, I want to send control input from Matlab to FlightGear and receive aircraft data from FlightGear to Matlab with UDP ...

fast 2 Jahre vor | 1 Antwort | 0

1

Antwort

Frage

How to calculate minimum singular value of I+L and I+inv(L) for MIMO system?
Hello, I want to calculate minimum singular value for MIMO system, and here is an example %% A = [0.1873 0.8403 -0.6003 -2.1...

mehr als 2 Jahre vor | 1 Antwort | 0

1

Antwort

Frage

What's the difference between two command?
Hello, In general, the command of nyquist plot is nyquist(sys,omega), but an example of textbook the command of nyquist is nyqu...

mehr als 2 Jahre vor | 1 Antwort | 0

1

Antwort

Discussion

How to maintain eigenvalues sequence
Hello, I have to draw root-locus for longitudinal motion; Short Period Mode and Phugoid Mode. Here is a code %% Dynamics Vp =...

mehr als 2 Jahre vor | 0

Frage

How to maintain eigenvalues sequence
Hello, I have to draw root-locus for longitudinal motion; Short Period Mode and Phugoid Mode. Here is a code %% Dynamics Vp =...

mehr als 2 Jahre vor | 0 Antworten | 0

0

Antworten