Community Profile

# Priyanshu Mishra

Last seen: 2 Tage ago Active since 2019

#### Content Feed

View by

i want to get wind speed wind direction quiver
Hi Young, You may refer to following problem, which has a similar query: https://www.mathworks.com/matlabcentral/answers/34065...

etwa 2 Jahre ago | 0

Fourier Transform of tripuls
Hi Moisa, fft is giving you a complex double values . Try taking only absolute values. I tried the following code and getting s...

etwa 2 Jahre ago | 0

Micro CT data reading
Hi Yasaween, To start with MATLAB and Simulink I can suggest you to go through the following training provided by MathWorks : ...

etwa 2 Jahre ago | 0

| accepted

I need to get the result for a unit step input at 0 s and a unit negative step disturbance at 25 s. But I am not understanding how to give the input
Hi Manideep For unitstep input , you may refer the following documentation: https://www.mathworks.com/help/signal/gs/impulse-s...

etwa 2 Jahre ago | 0

AppDesigner Lamp showing Calculation
Hi Kaan, You may refer for the following document for information on the app designer https://www.mathworks.com/help/matlab/c...

etwa 2 Jahre ago | 0

| accepted

Create a block system with Matlab and open it in Simulink
Hi Davide, You can create the similar model in simulink. For more information , you may refer the below document : https://www...

etwa 2 Jahre ago | 0

Normalized Histogram(area under curve unity) of the position angle.
Hi Manmeet, You may refer the following answer https://www.mathworks.com/matlabcentral/answers/24477-plotting-a-normalised-hi...

etwa 2 Jahre ago | 0

Signal logging through command line
Hi Mariam, You may visit the following answer as it has similar problem https://www.mathworks.com/matlabcentral/answers/44148-...

etwa 2 Jahre ago | 0

Frequency vs Amplitude plot using ODE45
Hi Ismail You may refer to following documentation for solving differential equation using ode45 and plotting your solutions: ...

etwa 2 Jahre ago | 0

Reading Serial Data on Arduino into Matlab
Hi Justin, You may refer the following link for reading streaming data from Arduino https://www.mathworks.com/help/matlab/mat...

etwa 2 Jahre ago | 0

how to control speed of the motor by using the rectifer inverter and motor circuit
Hi Maheshwari, You may visit to following link, for more information about PWM rectifier model for AC drives. https://www.math...

etwa 2 Jahre ago | 0

What will happen if sampling rate is less than Nyquist rate?
Hi Jami, According to Nyquist rule, the sampling frequency in this case should be more than 1000 Hz. To get more idea about, ...

etwa 2 Jahre ago | 0

Signal Analysis and Reconstruction
Hi Loren, You may see the documentation of concatenate to know more about this function.

etwa 2 Jahre ago | 0

Not Enough Input Arguments
Hi Sagar, You may refer to following documentation of xlsread . https://www.mathworks.com/help/matlab/ref/xlsread.html#btg5vmt...

etwa 2 Jahre ago | 0

How to derive Q-factor from BER?
Hi Alina, Since I do not have your code, I have written a small code. You may refer to it: ber = 2*10^-4 syms ber Q eqn = 0....

etwa 2 Jahre ago | 0

Convert complex number to phase shift in simulink
Hi Bamboo, In my understanding, there are couple of blocks which might be helpful for you. 1. Complex to magnitude angle 2. ...

etwa 2 Jahre ago | 0

How to search for where a function is used in Simulink Model
Hi Michael, Which item displays the full path of the item. If item is a MATLAB function in a Simulink model, then which display...

etwa 2 Jahre ago | 0

Graphing complex fourier series
Hi Santiago, You are getting this warning because you are attempting to plot a complex input with plot function. If you want to...

etwa 2 Jahre ago | 0

Solving difference equation using DFT
Hi Vishwajit, You may use the following code for your reference to solve above difference equation N = 8; a = [1 4 -1]; b = ...

mehr als 2 Jahre ago | 0

Doubt on uitable on inserting particular number of rows and columns
Hi Lokesh, I have written a small code for your reference. You can proceed with this code f = figure; uit = uitable(f) d = ...

mehr als 2 Jahre ago | 0

| accepted

Generate C++ code from standalone stateflow chart
Hi Meram, You can use Simulink Coder software to generate standalone C or C++ code from your Physical Networks models. you may ...

mehr als 2 Jahre ago | 0

lauch simulink simulation from windows command prompt

mehr als 2 Jahre ago | 0

Implementation of DIF FFT
Hi Vishwajith, Please refer to the following link. The similar problem is asked earlier as well. This link might help you. htt...

mehr als 2 Jahre ago | 0

| accepted

How to use Power Spectral density block in Simulink?
Hi Vineeth, Power Spectral Density block displays the frequency content of the buffer in graph window. The block calculates the...

mehr als 2 Jahre ago | 0

Error due to multiple causes in Simulink block diagram
Hi Linee, The error is due to the "From worksapce" block, which you are using in your model. The first collumn of your data (wh...

mehr als 2 Jahre ago | 0

how can I add a dielectric surface, like the terrain, in the antenna toolbox
Hi Ernst, You may use any of the installed antenna for terrain modelling. For adding a dielectric surface, you can DielctricCat...

mehr als 2 Jahre ago | 0

Exporting model from workspace to Simulink
Hi Shafaq, You can directly import variable from workspace using block from workspace. For more information on this you may ref...

mehr als 2 Jahre ago | 0

How can I represent the following piecewise function in Simulink
Hi Idrak, You may refer to this link for using MATLAB function.

mehr als 2 Jahre ago | 0

| accepted