Yifeng Tang

MathWorks

Last seen: Today | Aktiv seit 2020

Followers: 10 Following: 0

Programming Languages:
Python, MATLAB, Fortran
Spoken Languages:
English, Chinese
Pronouns:
He/him
Professional Interests:
Physical Modeling, Simscape Fluids, Simscape, Heat and Mass Transfer, Thermodynamics and Heat Transfer

Statistik

All

RANG
181
of 297.457

REPUTATION
636

BEITRÄGE
0 Fragen
374 Antworten

ANTWORTZUSTIMMUNG
0.00%

ERHALTENE STIMMEN
75

Abzeichen anzeigen

Feeds

Beantwortet
Load simulation state in Simulink Coder generated C code
Hi @Zoltán Runyó, I think it's possible to do what you are envisioning using "Simulink Parameters" in the initial conditions. ...

etwa 9 Stunden vor | 0

Beantwortet
Error in the Documentation and Modeling of the Polytropic Process in Positive Displacement Compressors
Hi @ROBERTO, This looks like an error in the documentation to me right now. I measured a few more quantities from the model. ...

3 Tage vor | 0

| akzeptiert

Beantwortet
How can I properly include the effect of wall thermal in the geometry based Condenser Evaporator (2P-MA) block?
Hi Roberto, The R2025a release (still in pre-release as of 3/7/2025) now has wall-thermal mass as an option for several geometr...

3 Tage vor | 0

Beantwortet
Convert a 2013a multibody model to 2022b
Looks like some of the frames need a rotation. I'm not sure about what mechanism you are trying to model, but right now, the th...

4 Tage vor | 1

| akzeptiert

Beantwortet
How to control pressure gain and mass flow with Fixed Displacement Pump
Hi Nadir, From you model, I measured of 9.2MPa. This is consistent with the formula you showed. I believe when you put in th...

5 Tage vor | 0

Beantwortet
How can I reduce excessive bouncing in my small quadruped Simulink model using Spatial Contact Force settings while joints run in position mode?
I use the following guideline when parametrizing "hard-stop" in hydraulic components (like a cylinder). You may find this simil...

7 Tage vor | 0

| akzeptiert

Beantwortet
Modelling multistage expansion of compressed air in a single cylinder engine
Hi @Kyle I feel like the model should look similar to that diagram you have. Single-cylinder engines can be modeled using a Me...

13 Tage vor | 0

Beantwortet
Linking Mechanical and Hydraulic System Model in SIMSCAP MATLAB
The Translational Multibody Interface was first available in R2021a. Prior to that, such interface can be doen using force sens...

14 Tage vor | 0

Beantwortet
Adding input for valid parameter in Simscape block
Hi @Florian, I think it's possible. The Simscape code of this block is visible. You may find it in the Description tab of the...

14 Tage vor | 0

| akzeptiert

Beantwortet
Modelling a Dehumidifier with Simscape Fluids System Level Heat Exchanger(TL-MA) not possible?
The error is complaining that the parameters you've set don't make sense :p For example, you've set the operation condition to ...

14 Tage vor | 0

Beantwortet
On how to use the Two-Way Connection Block
Hi @CAME, I've seen this in earlier version of Powertrain Blockset examples. I took some snapshot from this "Conventional Vehi...

21 Tage vor | 0

| akzeptiert

Beantwortet
Model leaks in tanks and valves in a gas SIMULINK system
(Moved to Answer from Comments) It sounds like you have some values as a "standard" leak rate, is that right? I would assume y...

24 Tage vor | 0

Beantwortet
Bonjour, je souhaite modéliser un piston et j'ai une erreur. Merci
In your model, the B & F ports of the prismatic joint is connected to the B & F port of a rigid transform block. This will fix ...

27 Tage vor | 0

Beantwortet
PEM fuel cell heat management
Looks like it should be instead. Would you agree? I checked the source code and the power dissipation term is calculated as ...

28 Tage vor | 1

Beantwortet
Trace Gas Removal Loop
Hi Ryan, The logic you have in mind is likely to trigger lots of zero-crossing/chattering, and as @Walter Roberson pointed out,...

etwa ein Monat vor | 1

Beantwortet
How to model Concave Hull Contact Force in Simulink Simscape
For a generic solid, Multibody only support exporting the Convex Hull for contact modeling (as of R2025a). So that quarter pipe...

etwa ein Monat vor | 0

Beantwortet
how to understand and combine simscape pump performance curves
I can try to help on the "Plotting on the Same Graph" part. Once you generate this figure from the pump block, you can use the ...

etwa 2 Monate vor | 0

| akzeptiert

Beantwortet
LNG liquid to gas phase change simulation Simscape
Hi @Anil I suggest that you try something like this: Model the LNG and its evaporization in the 2P domain. The Receiver Acc...

etwa 2 Monate vor | 1

| akzeptiert

Beantwortet
What is my fault to this modelling? I want to move the model but I am not able to solve the faults.
Follow the instructions in the error message. Use the Simulink-PS Converter to provide derivatives. The time constant will c...

etwa 2 Monate vor | 0

Beantwortet
Modelling the sublimation of dry ice
Hi @Kyle, Interesting problem. I would approach it from the angle of convervation of energy and mass. Assuming the dry ice st...

etwa 2 Monate vor | 2

| akzeptiert

Beantwortet
How to model a piston with a retracting spring at one end and having single hydraulic port??
Something like this should work. It's important to pay attention to a few things when setting up this model: (1) area of the...

etwa 2 Monate vor | 0

Beantwortet
Implementing Process Control for Heat Exchanger Networks in MATLAB
For the physical plant, for instances heat exchangers, pipes, valves, pumps, etc., I suggest that you look into Simscape and Sim...

etwa 2 Monate vor | 0

Beantwortet
Lead screw driven by a revolute joint in Simscape Multibody: How can I set a slider displacement to be proportional to the revolute joint angle?
Hi @mhaz, I think it would make more sense to move the revolute joint to be in series with the prismatic joint. See below. ...

2 Monate vor | 0

Beantwortet
How to measure torque and rpm of compressor in refrigeration cycle?
Use a Ideal Torque Sensor, connect it in series with the compressor R port, and now you are measuring the shaft torque. Multipl...

3 Monate vor | 0

Beantwortet
How to plot coefficient of performance(COP) of refrigerationcyclemodelexample?
For an air conditioning system, the COP is defined as the ratio between the cooling power and the compressor work. There are tw...

3 Monate vor | 0

Beantwortet
MATLAB Projects for Mechanical Engineers
Hi Saurav, A few things to check out on fileexchange: Ivan Liebgott (2024). Modeling and Simulation of Multi-Physics Systems w...

3 Monate vor | 0

Beantwortet
Network coupler for gas
Network coupler for Gas or Moist Air domain doesn't exist as of R2024b. I see two options: (1) follow the structure of such co...

4 Monate vor | 0

| akzeptiert

Beantwortet
How are centrifugal pump(TL) outlet flow rate and actual brake power calculated with pump nominal parameters?
In the equation for the reference capacity: , the first term on the RHS is the volumetric flow rate. If you move that term t...

4 Monate vor | 0

| akzeptiert

Beantwortet
I don' know why simulink parameter estimation failed. Please help me
Looks like the error message is trying to tell you that the Parameter Estimater cannot change the parameters it tries to estimat...

4 Monate vor | 1

| akzeptiert

Beantwortet
How can I determine the distance at which a moving frame slides over a fixed frame, knowing that I use a prismatic joint between these two frames?
You can set limits in the prismatic joint. It'll apply an additonal spring & damper once the limit is reached and try to stop t...

4 Monate vor | 0

Mehr laden

Yifeng Tang

MathWorks

Statistik

MATLAB Answers

MATLAB Answers

MATLAB Answers

File Exchange

MATLAB Answers

File Exchange

File Exchange

MATLAB Answers

MATLAB Answers

Feeds