Model Configuration Parameters for NXP FRDM-K64F Board

Hardware Implementation Pane Overview

Default Hardware Implementation Pane

Configure hardware board to run Simulink^® models.

1. In the Simulink Editor, select Simulation > Model Configuration Parameters.

2. In the Configuration Parameter dialog box, click Hardware Implementation.

3. Set the Hardware board parameter to NXP FRDM-K64F.

4. The parameter values under Hardware board settings are automatically populated to their default values.

   You can optionally adjust these parameters for your particular use case.

5. To apply the changes, click Apply.

For more information on selecting a hardware support package and general configuration settings, see Hardware Implementation Pane.

Build Options

Parameter	Description	Default Value
Build action	Defines how Simulink Coder™ responds when you build your model.	Build, load, and run
Firmware	The firmware chosen during the setup to run your model on the board.	mbed's CMSIS-DAP firmware (Default)

Clocking

Parameter	Description	Default Value
CPU Clock (MHz)	The CPU clock frequency in MHz.	120

DAC

Parameter	Description	Default Value
DAC0 reference voltage	Sets the reference voltage for digital to analog conversion.	DACREF_1

UART0

Parameter	Description	Default Value
Baud rate (in bits/s)	Defines the rate at which data is transferred over a serial line.	115200
Tx Pin	Sets the transmitting pin of UART0.	PTB17 (USBTX)
Rx Pin	Sets the receiving pin of UART0.	PTB16 (USBRX)
Parity	Determines whether the UART0 generates and checks for even parity or odd parity.	None
Stop bits	Sets the number of stop bits to indicate end of a packet.	1

UART1

Parameter	Description	Default Value
Baud rate (in bits/s)	Defines the rate at which data is transferred over a serial line.	115200
Tx Pin	Sets the transmitting pin of UART1.	PTC4 (D9)
Rx Pin	Sets the receiving pin of UART1.	PTC3 (D7)
Parity	Determines whether the UART1 generates and checks for even parity or odd parity.	None
Stop bits	Sets the number of stop bits to indicate end of a packet.	1

UART2

Parameter	Description	Default Value
Baud rate (in bits/s)	Defines the rate at which data is transferred over a serial line.	115200
Tx Pin	Sets the transmitting pin of UART2.	PTD3 (D12)
Rx Pin	Sets the receiving pin of UART2.	PTD2 (D11)
Parity	Determines whether the UART2 generates and checks for even parity or odd parity.	None
Stop bits	Sets the number of stop bits to indicate end of a packet.	1

UART3

Parameter	Description	Default Value
Baud rate (in bits/s)	Defines the rate at which data is transferred over a serial line.	115200
Tx Pin	Sets the transmitting pin of UART3.	PTC17 (D1)
Rx Pin	Sets the receiving pin of UART3.	PTC16 (D0)
Parity	Determines whether the UART3 generates and checks for even parity or odd parity.	None
Stop bits	Sets the number of stop bits to indicate end of a packet.	1

Ethernet

Parameter	Description	Default Value
Ethernet host name	Defines the local host name.	FRDM_K64F
MAC address	Defines the physical network address of the board.	00-CF-52-35-00-01
Enable DHCP for local IP address assignment	Configures the board to get an IP address from the local DHCP server on the network.	on
Board IP address	Sets the IP address of the board.	192.168.1.102
Subnet mask	Sets the subnet mask for the board.	255.255.255.0
Gateway	Sets the gateway required to access the target computer.	192.168.1.1

External Mode

Parameter	Description	Default Value
Communication interface	Transport layer used to exchange data between host and hardware.	Serial
Verbose	View external mode execution progress and updates.	off