Manikandan
anna university
Followers: 0 Following: 0
Statistik
RANG
2.823
of 301.097
REPUTATION
22
BEITRÄGE
4 Fragen
46 Antworten
ANTWORTZUSTIMMUNG
0.0%
ERHALTENE STIMMEN
8
RANG
3.575 of 21.169
REPUTATION
432
DURCHSCHNITTLICHE BEWERTUNG
4.80
BEITRÄGE
3 Dateien
DOWNLOADS
10
ALL TIME DOWNLOADS
4131
RANG
of 172.778
BEITRÄGE
0 Probleme
0 Lösungen
PUNKTESTAND
0
ANZAHL DER ABZEICHEN
0
BEITRÄGE
0 Beiträge
BEITRÄGE
0 Öffentlich Kanäle
DURCHSCHNITTLICHE BEWERTUNG
BEITRÄGE
0 Discussions
DURCHSCHNITTLICHE ANZAHL DER LIKES
Feeds
PI control techniques for speed control of a BLDC motor
Try to use trial and error method
fast 8 Jahre vor | 0
How to change Simulink model line widths
Don't take screen shoot. Go to edit, then copy model to clipboard. after past it as picture in your word. hence the quality of p...
fast 10 Jahre vor | 3
Gesendet
Measure the Frequency of given input Square wave
Contact: electricmani@yahoo.co.in
fast 10 Jahre vor | 1 Download |
how to control the position of a DC motor by FLC
i completed the same, refer this link, if you want more clarification write me: electricmani@yahoo.co.in http://ieeexplore.ie...
fast 10 Jahre vor | 0
Why is the induction motor speed very low and at a negative value
set your scope parameter setting, uncheck limited data points. reduce torque as zero.
fast 10 Jahre vor | 0
How to control a brushless motor through a ESC with C2000 using "Embedded Coder" Library in Simulink
I did same like, write me: electricmani@yahoo.co.in
fast 10 Jahre vor | 0
i am unable to get proper operations at 10 KHz speed of the "Repeating Sequence" block of Simulink under SimPowerSystems/Control& Measurements Library. With time values [0 1e-4 1e-4] for values [0 1e-4 0] the output is zero when run for 1 sec.
For 10khz output, use time value: (0 (1/10e3) and amplitude value: (0 1), then use less sampling time in solver, typically 2e-6 ...
fast 10 Jahre vor | 0
Is this the proper way to implement PID for 3 Phase inverter induction motor speed control?
Lot of theoretical methods available to find KP, Ki and Kd values, my suggestion for beginner try to do trial and error method. ...
fast 10 Jahre vor | 0
speed control of dc motor using SMC
First start open loop control of motor, verify with closed loop conventional PID controller, then change into SMC.
fast 10 Jahre vor | 0
Use PWM to control Speed of brushless dc motor!
use AND gate instead of product block. for more details contact me: electricmani@yahoo.co.in
mehr als 10 Jahre vor | 1
how to find the setpoint ref input block in simlink for design of PI controller to control speed of servo motor... i can't find the setpoint bock in simulink.... setpoint ref input block...
use constant block
mehr als 10 Jahre vor | 2
i want to control speed of DC motor using arduino via matlab.
use PWM
mehr als 10 Jahre vor | 0
how to do simulation of speed control of three phase induction motor by v/f method
Contact me: electricmani@yahoo.co.in
mehr als 10 Jahre vor | 1
How to implement speed control of induction motor using Fuzzy logic
Contact me: electricmani@yahoo.co.in
mehr als 10 Jahre vor | 0
How to specify time values and Output values for sawtooth waveform?
Time: [0 2.5000e-005] Output: [0 1]
mehr als 10 Jahre vor | 0
Tuning a pid controller. sampling times must agree?
Motor modeled as mathematical or taken from simpower system tool.
mehr als 10 Jahre vor | 0
Fixed Step Solver Problems
Reduce your sample time as much as possible to small.
mehr als 10 Jahre vor | 0
calculation of time difference between two crossings of voltage waveforms in simulink
Refer my paper: http://www.ripublication.com/ijaer_spl/ijaerv10n10_59.pdf
mehr als 10 Jahre vor | 0
How to determine the controller parameters for BLDC drive?
Refer slandered control system books for ZN method.
mehr als 10 Jahre vor | 0
torque ripple minimisation for bldc motor using direct torue control and indirect flux control
you need to mathematical modeling of motor.
mehr als 10 Jahre vor | 1
there is a built in model of brushless DC motor in simulink library. does anyone know the equations used for built in model of BLDC.
like it.
mehr als 10 Jahre vor | 0
Hi, i want to build an bldc motor in motor in matlab , i dont want to use an inbuilt motor block present in simulink .
I tried mathematical modeling of BLDC, but its result differ from simulik library BLDC motor. anybody have clear idea, post here...
mehr als 10 Jahre vor | 0
Servo motor controlling using MATLAB
Yes possible, but you need MATLAB supported hardware. what's your platform wish to work.
mehr als 10 Jahre vor | 0
Ball Screw driven XY table using AC servo motor.
Contact me @ electricmani@yahoo.co.in
mehr als 10 Jahre vor | 0
how to calculate parameters for dc servo motor simulation?
you should contact manufacture or google it to find required data's. not possible to find required data from the available data....
mehr als 10 Jahre vor | 0
Control Servo Motor
use analog output from the real time windows target tool box and select your DAQ via USB. then generate analog output voltage to...
mehr als 10 Jahre vor | 0
Tacho feedback in a servo
If you use simulink for DC motor position control, use motor output speed wm in rad/sec from measurement block. convert equivale...
mehr als 10 Jahre vor | 0
In which location ,we have to store the .fis file?
We need to import the file from work space or call where it was stored, before need to export designed fis to work space. me too...
mehr als 10 Jahre vor | 0
quadrature/rotary encoder .mdl file
I did the same things, if need help contact me on electricmani@yahoo.co.in
mehr als 10 Jahre vor | 0
