photo

Danikha Shyken


Last seen: 11 Monate vor |  Aktiv seit 2023

Followers: 0   Following: 0

Statistik

  • Thankful Level 4

Abzeichen anzeigen

Feeds

Anzeigen nach

Frage


Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?
this is the simulink model where the buck-boost controller is connected to the gate ports of each switch to power up the conve...

12 Monate vor | 1 Antwort | 0

1

Antwort

Frage


Hi. How do I maintain the square wave output of the 1-D?
the blue triangular waveform is the waveform of 1-D, and the red square wave is the D

12 Monate vor | 1 Antwort | 0

1

Antwort

Frage


Hi. In Simulink modeling, what can we do to ensure that the switching waveforms of the duty cycle and 1-duty cycle are not in phase?
q1 is the duty cycle (D), and q3 is the 1-duty cycle (1-D)

12 Monate vor | 2 Antworten | 0

2

Antworten

Frage


Hello. Could someone please suggest other components or blocks I can use to avoid using the step input block for the duty cycle?
Because I need the amplitude to reach 1.8V, and I only get 1V with the step input.

12 Monate vor | 1 Antwort | 0

1

Antwort

Frage


Could someone please assist me? My code for the buck-boost converter controller isn't working properly when I run it.
this is the Simulink model

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hello, if you have a moment, I could use your help in resolving this error.

etwa ein Jahr vor | 2 Antworten | 0

2

Antworten

Frage


Greetings, if you have a moment, I could use your help in resolving this error.

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hello, how do I feed the output of the input selector to the buck-boost converter using Simulink modeling?

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hey there, I need some help with this error. Would anyone be willing to provide guidance?
How do I reduce the fixed step size or tighten the error tolerances?

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hi there, I'm encountering an issue and would appreciate your guidance in resolving it.

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Greetings! I'm looking for assistance in understanding what's causing the problem in my code.
this is the MATLAB code: function y = determineMode(teg, pv, pzt, ~, D, ~, ~, ~, ~) % Inputs: % teg: Voltage from T...

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hey there, I need some help with this error. Your guidance would be valuable.

etwa ein Jahr vor | 0 Antworten | 0

0

Antworten

Frage


Hello, I'm in need of some help with this error.

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hi, would someone be willing to assist me in resolving this error

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


hey, could somebody please help me understand and resolve this error?

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


hello, can somebody help me figure out how to improve this Simulink model so that it has four output ports instead of a single output port?

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


hi, is the simulink model shown below possible?
we feed 4 input switches into a stateflow

etwa ein Jahr vor | 0 Antworten | 0

0

Antworten

Frage


Hello, can someone please help me understand this error?
I'm particularly confused about the part which says '... and the phase delay parameters of this block need to be integer multi...

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hello, I need help to resolve this error, please.

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hi, I need help with this error, please.

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hello, could someone kindly assist me in resolving this error?

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Can someone please help me learn how to make automatic switching based on available voltage sources to power up a three-input buck-boost converter?
An example of this operation would be: TEG: 0.3 - 0.4V PV: 0.4 - 1.2V PZT: 1.2 - 2V Ideal Output: 1.8V If the available...

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hi. Could someone please assist me in resolving this issue?

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Could someone please tell me which components are missing for this circuit to automatically and appropriately select inputs when dealing with multiple inputs?
3 inputs

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hi! I need some help. I'm confused as to why this selection mode circuit I modified won't work properly with three inputs.
1st input: 0.3 - 0.4V 2nd input: 0.4 - 1.2V 3rd input: 1.2 - 2V

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hello! Could someone kindly assist me in comprehending the purpose and operation of the system shown below?
This is one of the subsystems of an input selector circuit.

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


Hi! Could someone please provide me with an idea of how to model a selector for multiple inputs using Simulink? Thank you.
Input sources: Thermoelectric Generator(TEG), Photovoltaic(PV), and Piezoelectric(PZT)

etwa ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


What should be the inductor initial current and capacitor initial voltage with an input range of 0.02-0.16V
for a two MOS switch two diodes buck-boost converter with an input of 0.02V, resistor load of 2,142,857.143 Ω, inductance of 1 m...

mehr als ein Jahr vor | 1 Antwort | 0

1

Antwort

Frage


What should be the initial value of the inductor and capacitor with an input range of 0.02-0.16V
For a two MOS switch two diodes buck-boost converter with an input of 0.02V, resistor load of 2,142,857.143 Ω, inductance of 1 m...

mehr als ein Jahr vor | 0 Antworten | 0

0

Antworten