# Yash

Last seen: etwa 2 Monate vor Aktiv seit 2022

Followers: 0   Following: 0

#### Statistik

Abzeichen anzeigen

#### Feeds

Anzeigen nach

Beantwortet
How to create overlaping heatmap in geoplot
To achieve a discrete density plot with overlapping circles of different colors, you can use the scatter function in MATLAB. Thi...

3 Monate vor | 0

| akzeptiert

Beantwortet
calculate the average of each face ?
To calculate and plot the average for each face, you can use the accumarray function in MATLAB. Lets assume you have the time se...

3 Monate vor | 0

Beantwortet
pde-bvp in MATLAB?
To solve a boundary value problem (BVP) for a partial differential equation (PDE) in MATLAB, you can use the pdepe function. Alt...

3 Monate vor | 0

Beantwortet
Difficulty getting s2rlgc to work
If the makepassive function is not producing acceptable results for the s2rlgc function, you may need to investigate further to ...

3 Monate vor | 0

Beantwortet
How can I calculate the SNR of a curve that has impulse noise added?
To calculate the SNR (Signal-to-Noise Ratio) of a signal in MATLAB, you can follow these steps: % Calculate the power of the si...

3 Monate vor | 0

Beantwortet
Error when using "Resample and Smooth Surfaces" function in CAT12
The error message you're encountering, "Unrecognised function or variable 'Psname'." suggests that there's a reference to an und...

3 Monate vor | 0

Beantwortet
polynomial function to transfer function in matlab
Yes, you can obtain the transfer function of a 4th order polynomial equation in MATLAB. However, it is important to note that a ...

3 Monate vor | 0

Beantwortet
Is it possible to simulate/code CD-NOMA schemes such as SCMA, LDS CDMA in MATLAB?
Yes, it is possible to simulate and code CD-NOMA schemes such as SCMA (Sparse Code Multiple Access) and LDS CDMA (Low Density Si...

3 Monate vor | 0

Beantwortet
Array iteration using a for loop in stateflow
Given the complexity and the size of your data (44608 different trajectories for a 6-axis robot), a direct for loop approach mig...

3 Monate vor | 0

| akzeptiert

Beantwortet
Defining vector of integrals with undefined function
Hey, Your code looks almost correct. The only issue is with the syntax of the integral function. You should replace integrate w...

4 Monate vor | 0

Beantwortet
Elliptical Pressure Distribution Function
Hi, You can obtain an elliptical distribution for your "Pressure Factor" using the equation of an ellipse. Here's the code that...

4 Monate vor | 0

Beantwortet
Reinforcement learning - DDPG - minibatch - Continuos action saturation
The minibatch size in a neural network training process refers to the number of samples used in each iteration to update the wei...

4 Monate vor | 0

Beantwortet
How to reduce the color intensity of a noise signal?
Hi, To decrease the color intensity of the noise before adding it to the PD signal, you can adopt one of the following approach...

4 Monate vor | 0

Beantwortet
Reinforcement Learning - Access agent/training parameters while training
Normally, when you use the train function, it should open up the Reinforcement Learning Episode Manager. This tool allows you to...

4 Monate vor | 0

Beantwortet
I keep getting an error When I train an agent with DDPG: Error using rl.env.SimulinkEnvWithAgent>localHandleSimoutErrors (line 667)
Hi, I am assuming you are using R2020a or lower versions of MATLAB. Similar error as to what you are facing is identified in th...

4 Monate vor | 0

Beantwortet
How to train selforgmap with trajectories?
Hi, To train a selforgmap with trajectories, you need to reshape your trajectory data into a suitable format for training. The ...

4 Monate vor | 0

Beantwortet
External Mode Open Protocol Connect command failed
I am assuming you are using MATLAB R2020b or R2021a version. The error that you are facing is related to connection error during...

4 Monate vor | 0

Beantwortet
Solution to Robustness Bound Equation
To solve equation (2) using the value of P obtained from equation (3), you can find the maximum of the singular value decomposit...

4 Monate vor | 0

Beantwortet
Calculating volume of a convex hull
You are getting that error because all your points are coplanar, and you are trying to find the convex hull in 3D of a 2D figure...

4 Monate vor | 0

Beantwortet
What types of analysis can i perform on the videos of drawings?
Hello, For video analysis of the creation of drawings, besides optical flow, you can also consider the following techniques: M...

4 Monate vor | 0

Beantwortet
solving non linear equation
To obtain a matrix (i, k) instead of a vector, you can preallocate the matrix S before the loop and assign the values inside the...

4 Monate vor | 0

Beantwortet
Plot the principle axes from regionprops3 over an isoplot of an ellipsoid
The issue with your code is that the quiver3 function expects the direction vectors to be normalized. In your code, you are dire...

4 Monate vor | 0

Beantwortet
Matlab 2021b Simulink Data Inspector automatic overlay and overwrite no longer present
Hey Nipun, In MATLAB 2021b, the Data Inspector tool has undergone some changes in its default behavior. By default, the tool no...

5 Monate vor | 0

Beantwortet
Matlab2021b constantly fails to invoke parpool
Hi, When operating on Windows with MATLAB R2021b, users with non-ASCII characters in their usernames, such as extended ASCII ch...

5 Monate vor | 0

Beantwortet
how to plot higher order levels of the wavelet scattering transform?
Hi Lucrezia, Once you have already computed the scattering transform coefficients and stored them in a variable, you can use th...

5 Monate vor | 0

Beantwortet
ert static function declaration when using newer versions of matlab
Hi Martin, It seems that the issue you're facing is related to the static declaration in your custom TLC file. Starting from MA...

5 Monate vor | 0

Beantwortet
"RecordingArrays cannot be used across tapes" when backpropagating dlode45
Hi, The error "RecordingArrays cannot be used across tapes" is thrown when using dlgradient with the 'GradientMode="adjoint"' o...

5 Monate vor | 0

Beantwortet
bwboundaries() C++ code Generation Error
Hi, The error message indicates that Simulink is having trouble determining the output sizes for a block within the 'corner_det...

5 Monate vor | 0

| akzeptiert

Beantwortet
Raspberry 4B Code replacement library Arm Cortex-A ne10 error!
Hi, The error message indicates that the current compilation process is utilizing the Thumb instruction set, which is a condens...

5 Monate vor | 0

Beantwortet
Antenna array (Transmitter + Receiver) in Matlab
Hi Farha, To facilitate the design and simulation of sensor arrays for applications like wireless communication and radar, you ...

5 Monate vor | 0