Nivedita

MathWorks

Last seen: 2 Tage vor | Aktiv seit 2022

Followers: 0 Following: 0

Nachricht

I am an Engineer in the Engineering Development Group at MathWorks. DISCLAIMER: All opinions I express on this forum are my own, and not representative of MathWorks.

Programming Languages:
Python, C++, C, MATLAB, HTML, CSS
Spoken Languages:
English, Hindi, Bengali

Statistik

All

Abzeichen anzeigen

Feeds

Beantwortet
C2000 - Issue Running Monitor and Tune in Simulink Model
Hello, TMDSCNCD28379D is a controlCARD. The onboard XDS100v2 USB connection exposes multiple logical interfaces in Windows. In ...

ein Tag vor | 0

Beantwortet
Eror Timeout problem with F28335 board, XCP internal error, timeout expired
Hello, This error usually means that the model was built and programmed, but Simulink could not establish the Monitor & Tune / ...

2 Tage vor | 0

Beantwortet
Error: Could not connect to target application: XCP internal error: timeout expired, in response to XCP CONNECT command
Hello, This error usually means that the model was built and programmed, but Simulink could not establish the Monitor & Tune / ...

2 Tage vor | 0

Beantwortet
Hardware tools and blocks
Hello Salah, The GPIO block only writes a digital value from software at the model sample time. That can work for slow/manual p...

2 Tage vor | 0

Beantwortet
use of Base rate trigger
Hello Mohammad Tauquir Iqbal, The Base rate trigger selects the interrupt source that runs the model's base-rate scheduler on t...

2 Tage vor | 0

Beantwortet
A FRDM-K64F board cannot be detected
Hello nicai, The code generation step completed successfully. The failure occurs during deployment, when MATLAB tries to detect...

2 Tage vor | 0

Beantwortet
S-Function builder
Hi Gaston, The errors that you are observing are probably because target-specific C2000 code is being compiled during the simul...

2 Tage vor | 0

Beantwortet
XCP internal error: timeout expired' error during 'Monitor and Tune' for STM32F767ZI
You can refer to the following link for external mode debugging steps: https://www.mathworks.com/matlabcentral/answers/2048172-w...

2 Tage vor | 0

Beantwortet
The data for selected hardware TMS320F28379D is invalid
Hello Kshitija Nand Kumar, The issue that you are facing might be due to a corrupted config set. Please try to check if you are...

3 Tage vor | 0

Beantwortet
Embedded Coder Support Package for Texas Instruments C2000 Processors
Hi, You can use the C2000 Microcontroller Blockset which is available from R2023a. It supports Linux environment from R2023a. ...

29 Tage vor | 0

Beantwortet
Data gaps and aliasing in Simulink External Mode with TI LaunchPad at 100µs sample rates
Hi Sanjit, The Monitor and Tune feature operates in the background and inherently requires a finite amount of time to process a...

29 Tage vor | 0

Beantwortet
C2000 CAN Video example calls out eCAN, but blockset shows CAN and we have an RX Issue
Hi Ali, You can refer to these following examples for your usecase: Communication using CAN blocks: https://www.mathworks.com/...

etwa 2 Monate vor | 0

Beantwortet
how to use FPUfastRTS library on Ti F28377S
Hello Valeriy, On devices supporting both TMU and FPU, select Enable TMU for more optimized floating-point math routines. This ...

2 Monate vor | 0

Beantwortet
FIL Error: "Did not receive version information" with connection that works in Vivado
Hello, You can follow the troubleshooting steps mentioned in the official documentation to resolve the issue: https://www.math...

etwa ein Jahr vor | 0

Beantwortet
Cannot open .mlapp file in app designer
Hello Daniel! I understand that whenever you are trying to open the attached app, you are getting the dialog box with “Error lo...

fast 3 Jahre vor | 0

Beantwortet
May I know why 'value must be a double scalar' come out in app designer?
Hello Aqilah! I understand that you are receiving the error “ 'Value' must be a double scalar” in app designer. I am assuming ...

fast 3 Jahre vor | 0

Gelöst

Make roundn function
Make roundn function using round. x=0.55555 y=function(x,1) y=1 y=function(x,2) y=0.6 y=function(x,3) ...

etwa 4 Jahre vor

Gelöst

Matlab Basics - Rounding III
Write a script to round a large number to the nearest 10,000 e.g. x = 12,358,466,243 --> y = 12,358,470,000

etwa 4 Jahre vor

Gelöst

Matlab Basics - Rounding II
Write a script to round a variable x to 3 decimal places: e.g. x = 2.3456 --> y = 2.346

etwa 4 Jahre vor

Gelöst

Check that number is whole number
Check that number is whole number Say x=15, then answer is 1. x=15.2 , then answer is 0. http://en.wikipedia.org/wiki/Whole_numb...

etwa 4 Jahre vor

Gelöst

MATLAB Basic: rounding IV
Do rounding towards plus infinity. Example: -8.8, answer -8 +8.1 answer 9 +8.50 answer 9

etwa 4 Jahre vor

Gelöst

MATLAB Basic: rounding III
Do rounding towards minus infinity. Example: -8.8, answer -9 +8.1 answer 8 +8.50 answer 8

etwa 4 Jahre vor

Gelöst

MATLAB Basic: rounding II
Do rounding nearest integer. Example: -8.8, answer -9 +8.1 answer 8 +8.50 answer 9

etwa 4 Jahre vor

Gelöst

MATLAB Basic: rounding
Do rounding near to zero Example: -8.8, answer -8 +8.1 answer 8

etwa 4 Jahre vor

Gelöst

Fibonacci sequence
Calculate the nth Fibonacci number. Given n, return f where f = fib(n) and f(1) = 1, f(2) = 1, f(3) = 2, ... Examples: Inpu...

etwa 4 Jahre vor

Gelöst

Roll the Dice!
*Description* Return two random integers between 1 and 6, inclusive, to simulate rolling 2 dice. *Example* [x1,x2] =...

etwa 4 Jahre vor

Gelöst

Magic is simple (for beginners)
Determine for a magic square of order n, the magic sum m. For example m=15 for a magic square of order 3.

etwa 4 Jahre vor

Gelöst

Reverse the vector
Reverse the vector elements. Example: Input x = [1,2,3,4,5,6,7,8,9] Output y = [9,8,7,6,5,4,3,2,1]

etwa 4 Jahre vor

Gelöst

Sum all integers from 1 to 2^n
Given the number x, y must be the summation of all integers from 1 to 2^x. For instance if x=2 then y must be 1+2+3+4=10.

etwa 4 Jahre vor

Gelöst

Return area of square
Side of square=input=a Area=output=b

etwa 4 Jahre vor

Mehr laden