Statistik
13 Fragen
0 Antworten
RANG
105.307
of 300.759
REPUTATION
0
BEITRÄGE
13 Fragen
0 Antworten
ANTWORTZUSTIMMUNG
30.77%
ERHALTENE STIMMEN
0
RANG
of 21.081
REPUTATION
N/A
DURCHSCHNITTLICHE BEWERTUNG
0.00
BEITRÄGE
0 Dateien
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANG
of 170.900
BEITRÄGE
0 Probleme
0 Lösungen
PUNKTESTAND
0
ANZAHL DER ABZEICHEN
0
BEITRÄGE
0 Beiträge
BEITRÄGE
0 Öffentlich Kanäle
DURCHSCHNITTLICHE BEWERTUNG
BEITRÄGE
0 Discussions
DURCHSCHNITTLICHE ANZAHL DER LIKES
Feeds
Frage
How can I obtain the difference between two data stored in workspace?
I experimentally tested a motor and the measured speed and the reference speed were stored in the workspace. My supervisor aske...
etwa 2 Jahre vor | 1 Antwort | 0
1
AntwortFrage
How to execute the same code for a specific time?
I want to estimate the shaft speed of a motor and to do that I obtain the speed error between the reference speed and the estima...
fast 3 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Position error of motor shaft
I want to obtain the position error of motor shaft so I subtracted the estimated position from the measured position. modulus f...
etwa 3 Jahre vor | 1 Antwort | 0
1
AntwortFrage
how to export varied variable to saturation block in Simulink?
I tried to use varied value in the Saturation block and this value (called flux) exported from the output of a lookup table? I u...
etwa 3 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Use a command only once
I use a code to search for an accurate rotor position. I used an initial value for the position (theta_b=0) as shown below and t...
mehr als 3 Jahre vor | 2 Antworten | 0
2
AntwortenFrage
Code error in MATLAB function block.
I wrote a code in a MATLAB function block that consists of two inputs one input for the signal that needs to be filtered and the...
mehr als 3 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Calculate cycle time for a signal by code
I want to calculate the cycle time for a signal (the frequency) by using a code (Matlab function block). For examble, in a motor...
fast 4 Jahre vor | 0 Antworten | 0
0
AntwortenFrage
Why the amplitude of the 90 shifted phase signal when use the analytic signal block is not equal to the original signal?
I could manage to shift the phase of signal by 90 by using analytic signal block. But, the problem is that its amplitude is not ...
mehr als 5 Jahre vor | 1 Antwort | 0
1
AntwortFrage
how to shift phase of unknown frequency signal by 90 by using hilbert transform?
I tried to shift an unknown frequency signal by 90 by applying hilbert transform comand (imag(hilbert(x)) in matlab function blo...
mehr als 5 Jahre vor | 0 Antworten | 0
0
AntwortenFrage
How to connect simulink blocks with RF blocks (interface)?
I tried to use simulink blocks with RF blocksets but they can not be connected to each other. I think there is an interface betw...
mehr als 5 Jahre vor | 1 Antwort | 0
1
AntwortFrage
How to shift a signal in simulink by 90 degrees?
I want to shift a signal by 90 degrees. there is a block called phase shift in RF blockset, but it cannot be used with simulink....
mehr als 5 Jahre vor | 1 Antwort | 0
1
AntwortFrage
A problem with the solver
A problem with the solver when I run a model. when I disconnect the gate driver (simulink) from the inverter (simcap) the proble...
mehr als 5 Jahre vor | 1 Antwort | 0
1
AntwortFrage
measuring the phase to neutral voltage in PMSM
in the MATLAB, how can I measure the voltage between the phase and the neutral point in the PMSM machine? (there is no access to...
fast 6 Jahre vor | 1 Antwort | 0
