Community Profile

photo

Jesús Zambrano


Last seen: Today

MathWorks

400 total contributions since 2018

Jesús Zambrano's Badges

  • Thankful Level 1
  • Revival Level 4
  • 6 Month Streak
  • Knowledgeable Level 2
  • Puzzler
  • Modeling And Simulation Challenge Master
  • Community Group Solver
  • Speed Demon
  • Leader
  • Commenter
  • Promoter
  • Creator
  • Introduction to MATLAB Master
  • First Answer
  • Solver

View details...

Contributions in
View by

Answered
Error in Test Harness Generation in SIL Verification Mode
I assume that the subsystem is part of a Simulink model, correct? Before creating the harness for the subsystem, make sure that ...

25 Tage ago | 1

| accepted

Answered
How to use Variant in stateflow? Means same like Variant subsystem in simulink.
The workflow is similar to when authoring variant models or variant subsystems. See the following link: https://se.mathworks.co...

25 Tage ago | 0

Answered
monitoring a signal trough time
Hi Sander, I think that what you are looking for is detailed in the following documentation https://se.mathworks.com/help/stat...

etwa ein Monat ago | 0

Answered
How to generate a quadratic signal in Simulink ?
Hi Simon, What if you try using the block Polynomial (you find it in the section 'Math Operations', in Simulink Library). With ...

etwa ein Monat ago | 0

Answered
Export requirements as document as at the training
You can go to the Requirement Editor (Apps tab, Requirement Manager, Requirement Editor) and go to the Report tab and click Gene...

etwa ein Monat ago | 0

Answered
How to Open Simulink Model Properties in fullscreen window?
You can also have access to the model callbacks by typing Ctrl+Shift+I, it opens the model Property Inspector on the right-hand ...

etwa ein Monat ago | 0

| accepted

Answered
Data variants in Simulink Data Dictionary
You can add a Simulink Variant to a Data Dictionary (see picture below). For example, programmatically V_LINEAR_CONTROLLER=S...

etwa 2 Monate ago | 0

Answered
How to calculate the error between the two signs
Could you narrow your question a bit more? What kind of error do you want to calculate? For example: percentage error?, mean sq...

etwa 2 Monate ago | 0

Answered
What does Ki*Ts mean in Discrete PI controller ?
From the documentation about the meaning of Ki*Ts, it indicates that: "You must premultiply the integral gain value by the integ...

etwa 2 Monate ago | 0

Answered
How to vary offset during simulation
Hi Luiz, You can include a slider (fomr the section Dashboard in the Library) in the Simulink model, and link it to the SineWav...

etwa 2 Monate ago | 0

Answered
Simulink model integration methods
Hi Pradeep, The answer to this question will require pages and pages. I recommend you to take a training course called Simulink...

etwa 2 Monate ago | 0

Answered
signal de-bounce in Simulink
The implementation looks OK. Actually, it is the same as the one recommended in the documentation https://www.mathworks.com/hel...

etwa 2 Monate ago | 0

| accepted

Answered
Course "Stateflow Onramp" doesn't load
Hi, The steps to follow depend on the relase, please check the 'How to Get Started' in this link: https://www.mathworks.com/le...

2 Monate ago | 0

Answered
Is Simulink Verification and Validation necessary to link and edit Requirements to my Stateflow model?
Simulink Requirements™ license should be sufficient. See: https://www.mathworks.com/help/simulink/ug/viewing-linked-requirement...

2 Monate ago | 0

Answered
creating baselines in simulink test
Use 'Capture' button if you want to record a baseline from the system under test. It will run the system under test and populate...

2 Monate ago | 0

Answered
Simulink menu bar on Matlab 2019b
For R2019a you can switch back to the old toolstrip, please see the way here: https://blogs.mathworks.com/simulink/2019/03/25/w...

2 Monate ago | 0

Question


Generalization of Catalan's conjecture
I would like to have a simple MATLAB code that can give the solutions for the generalization of the Catalan's conjecture for a g...

2 Monate ago | 1 answer | 0

1

answer

Answered
CANNOT FIND EXPLICIT SOLUTION
Hi Jiyoung, What I see from your code is that there is a variable 'y' which is a vector of 801 elements. Thas makes you to have...

2 Monate ago | 0

Answered
Error loading .mat
Could you replicate this behavior? I would also like to know the size of this mat-file.

2 Monate ago | 0

Answered
How to modify step size using my custom Simulink Block
From what I understand, you would like to change the step size of the Solver during time. Step size, as well as other parameters...

2 Monate ago | 0

Answered
How to solve error of creating harness model
Hi Kenji, The basic steps to create and load a harness programmatical are as follows: model = 'sltestCruiseChart'; load_syste...

2 Monate ago | 0

Answered
Values won't take from workspace
Not enough information about the problem here. Implementation seems OK. Have you run the model?, got any warning or error mess...

2 Monate ago | 0

Answered
Simulink block to equation conversion?
I´m afraid there is not such a workflow for that.

4 Monate ago | 0

Answered
simout block for simulink?
There is not such a block name in the library browser. Could you be more specific in the goal of this block in your model?

4 Monate ago | 0

Answered
how to link simulink and m file
Hi Amir, Your m-file should at least include the command sim in order to simulate the Simulink model programmatically. Read mor...

4 Monate ago | 0

Answered
What are the most frequently used Simulink blocks?
Hi Nick, Hard to find out this statistics. Intuition says that common blocks should include inport and outport blocks, Gain, Su...

4 Monate ago | 0

Answered
ert_main.c not generated
Hi Angelo, The option "Generate an example main program" in Code Generation of Configuration Parameters should be selected, see...

4 Monate ago | 0

Answered
What is the meaning of first two letters in MAAB guidelines ID?
Hi Manjit, Please read detail information of guideline template in the following link https://se.mathworks.com/help/simulink/m...

4 Monate ago | 0

Answered
How to change signal value at intermediate steps in Simulink?
Hi Luis, You could try include the sensor1 model in an enabled subsystem, https://www.mathworks.com/help/releases/R2019b/simu...

4 Monate ago | 0

Answered
Changing frequency of sine wave
Hi Pawel, This example might be useful to solve your question https://www.mathworks.com/help/releases/R2019b/comm/ug/fm-modula...

4 Monate ago | 0

Load more