Community Profile

photo

s0ter48


Last seen: 8 Tage ago Active since 2019

Programming Languages:
C++, MATLAB
Spoken Languages:
Arabic, English, German

Statistics

  • First Answer
  • Thankful Level 1

View badges

Content Feed

View by

Question


Surf plot 3D like the simulation manager
Hey guys, I would like to perform the surf plot with the data which results from the simulation manger calculations. I want to...

6 Monate ago | 0 answers | 0

0

answers

Answered
Counter for Sawtooth signal in Simulink
I had a small (condition) mistake... . But it should be fixed now. I don´t see any further mistakes or counting errors. If y...

7 Monate ago | 0

Answered
Counter for Sawtooth signal in Simulink
I created two counters now. counter #1 is doing what I want but some how there is a shift and he is loosing a sawtooth i thin...

7 Monate ago | 0

Answered
Gain block ignored :
Hey Guys, I have an similiar issue. I have an Signal which is not 0. Then I put an 0 Gain to it... with an parameter which i...

7 Monate ago | 0

Answered
Log simulink (variable step) data with with one sample time!
Thanks for the quick response. I am also logging data from simscape models (e.g.) which is internally in the blocks. How to ha...

7 Monate ago | 0

Question


Log simulink (variable step) data with with one sample time!
Hello guys, is there a way to log signals with one sample time? I habe an system model which works with variable steps. Form 1...

7 Monate ago | 3 answers | 0

3

answers

Question


Counter for Sawtooth signal in Simulink
Hello everybody, I'm trying to set up a round counter for my model. The round counter should count how many revolutions (360 °...

7 Monate ago | 4 answers | 0

4

answers

Question


Simulation Manager - Error during serialization
Hey Guys, I am using the Simulation-Manager it works pretty good. But when it comes to saving the mldatx file I get the erro...

8 Monate ago | 1 answer | 0

1

answer

Question


PMSM (simscape) No load test
Hey guys, I am trying to resolve my no load data out of my in simscape designed PMSM. With load it is no problem and the motor...

10 Monate ago | 1 answer | 0

1

answer

Answered
Back EMF Constant within the Simscape PMSM block
Hello guys, mathworks contacted me again and corrected their answer and provided me an example model. The simscape PMSM block ...

11 Monate ago | 0

Answered
Back EMF Constant within the Simscape PMSM block
Hello, I understand that we need a BackEMF constant peak and over one phase. In a DELTA connection it doesn´t matter because p...

11 Monate ago | 0

Question


Back EMF Constant within the Simscape PMSM block
Hello guys, in the Simscape PMSM block I want to type in the Back EMF constant (kE). But I cant find if I should give the data...

11 Monate ago | 3 answers | 0

3

answers

Question


Find Zero Crossing in Cell Aray with Vectors
Hello everybody, I have the following data: Time -> 25x25 cell X -> 25x25 cell Y -> 25x25 cell attached you will find a p...

etwa ein Jahr ago | 0 answers | 0

0

answers

Question


Simulink - How to prove if trigger signal exist or still running
Hi guys, I have an triggered subsystem in my model. When the there is no more trigger signal i want to set the output signal o...

etwa 2 Jahre ago | 0 answers | 0

0

answers

Answered
Using triggered subsystem with either - need a reset but how?
Hmm... nobody can help me with this?

etwa 2 Jahre ago | 0

Question


Using triggered subsystem with either - need a reset but how?
Hey guys, I need to use a triggered subystem to detect flanks (pos and neg) and calculate the time difference between these and...

etwa 2 Jahre ago | 2 answers | 0

2

answers

Question


Cut Sinusoidal signal in a integer number of periods
Hey guys, I have an measurement of three sinusoidal signals. But it is enough to only work with one in this case. The measu...

mehr als 2 Jahre ago | 1 answer | 0

1

answer

Answered
I need a code to separate each cycle of sine wave.
Hey guys, i know this is an old one but i can´t use this on my signals? And im not understanding why. Maby a dumb one but I ...

mehr als 2 Jahre ago | 0

Question


Simulink Knob is working but it is graphically only jumping between min and max value
Hey guys, im using a Knob (connected with an Gain) in my simulink modell and it is working but graphically it only jumping bet...

mehr als 2 Jahre ago | 0 answers | 0

0

answers

Answered
Replace Matlab FCN with Stateflow Chart - Error
No one a hint or an idea?

mehr als 2 Jahre ago | 0

Question


Replace Matlab FCN with Stateflow Chart - Error
Hi Guys, i replaced a working matlab fcn with a stateflow chart. To be honest i didnt expected any errors because it is very si...

mehr als 2 Jahre ago | 1 answer | 0

1

answer

Question


App designer - How To Re-Run an app
Hey guys, i have designed an app with app designer. In this app i habe an "run" button which runs a function within the app. ...

mehr als 2 Jahre ago | 1 answer | 0

1

answer

Question


Simulink If action subsystems -> ERROR!!
Hey guys, try to use to different subsystems by controlling them with a constant. The output of the two subsystems is the same ...

mehr als 2 Jahre ago | 0 answers | 0

0

answers

Question


App designer - How do i clear all variables?
Hey guys, I created an App within App designer. It works in mostly all cases perfect... except in one case. This case is if I...

mehr als 2 Jahre ago | 1 answer | 0

1

answer

Answered
Find jumps in Signal take constant area and split signal to different mat files
Maby an easier question. How do I get the first value when it reached the next jump? I mean if it gets constant (green lines) ...

mehr als 2 Jahre ago | 0

Question


Find jumps in Signal take constant area and split signal to different mat files
Hey guys, I have following Signal: I need to split this signal into different mat files. My problem i have the noise and th...

fast 3 Jahre ago | 2 answers | 0

2

answers

Question


Dynamic Legend with auto line break
Hey guys, I am using a DynamicLegend. with the following code: legend(ax(2),'-DynamicLegend', 'Orientation','horizontal','Fon...

fast 3 Jahre ago | 0 answers | 0

0

answers

Question


Robust edge/flank detection - HELP!!
Hey guys, i have an measurement and read in three rect. signals. I need to detect the pos. and neg. edges/flanks of the three ...

fast 3 Jahre ago | 1 answer | 0

1

answer

Question


Repeating x-axis for rectangular signal
Hey guys, i have an rectangular signal i want to plot. On the Y axis is the voltage from 0 to 3.3 V (24945x1 single) and on th...

fast 3 Jahre ago | 1 answer | 0

1

answer