photo

Arun Mathamkode

Last seen: 12 Tage vor |  Aktiv seit 2017

Followers: 0   Following: 0

Statistik

  • 12 Month Streak
  • Knowledgeable Level 4
  • Knowledgeable Level 3
  • Revival Level 3
  • First Review
  • First Answer

Abzeichen anzeigen

Feeds

Anzeigen nach

Beantwortet
How to locate the PX4 files which in wsl2 when I use the UAV ToolBox for PX4?
As Jacob mentioned, currently the default Ubuntu version for WSL2 is Ubuntu 24.04, which is not compatible with the PX4. You nee...

etwa ein Monat vor | 0

Beantwortet
UAV Toolbox Support Package for PX4 Autopilots - Hardware Setup Build PX4 Firmware Failed
PX4 is not recommending the Cygwin based workflow anymore. The toolchain was previously recommended, but does not work with PX4 ...

etwa ein Monat vor | 0

Beantwortet
How to set the control algorithm's execution frequency on the flight control board when using the UAV Toolbox Support Package for PX4 Autopilots?
The execution rate is defined by the sample time of your model. The base sample time is decided based on the Sample time paramte...

etwa 2 Monate vor | 0

Beantwortet
Adding MAVLINK messages for an external groundstation to use in telemetry (RFD-900)
You can consider using the DEBUG MAVLink message and DebugValue uORB message. The values written to DebugValue uORB message shou...

etwa 2 Monate vor | 0

Beantwortet
Accessing Pixhawk 6x parameters when building firmware for SRXL2 connection
As I understand from the links to the paramters mentioned, these are all ArduPilot parameters and you might not find them if you...

etwa 2 Monate vor | 0

Beantwortet
Error when buliding PX4 firmware with some deactivated modules
PX4 modules have interdependencies. So if you remove one module you have to remove the other as well. That is why the build is f...

2 Monate vor | 1

| akzeptiert

Beantwortet
UAV Tool Box Radio Control Transmitter maximum channels for use with Pixhawk
RC transmitter block is using the InputRc uORB message to read the RC signals. You can use uORB read block and select inputRC as...

3 Monate vor | 0

Beantwortet
How can I communicate between a Pixhawk controller and an actuator module using UAVCAN?
Starting in R2024b, you can use the PX4 Actuator Write block in your Simulink model to write motor and servo actuator values ove...

3 Monate vor | 0

| akzeptiert

Beantwortet
How can I integrate my custom reinforcement learning agent with the PX4 Autopilot architecture in Simulink, train it within this setup, and then deploy it onto a real drone?
It won't be easy to get an answer here if you ask the entire project as a question. I will recommend you go through individual d...

3 Monate vor | 0

Beantwortet
Hello, I own PX4 cube orange+. I can not make motor for drone run with px4 PWM Output block with that PX4 cube orange+. but it works for PX4. I use Matlab 2024a. help please!
Ensure that you are not in HITL mode and also use the latest update of UAV toolbox supportpackage for PX4 Autopilots. In the sc...

4 Monate vor | 0

Beantwortet
Why Matlab can not find the WSL2?
This issue is fixed in update 24.1.2. Go to Add-ons and see if there any update available for the UAV Toolbox support package fo...

5 Monate vor | 1

| akzeptiert

Beantwortet
Something wrong when I run the project in PX4 Autopilot in Hardware-in-the-Loop (HITL) Simulation with UAV Dynamics in Simulink
Can you try the following command ? [status,errmsg] = license('checkout','Aerospace_Blockset') I guess you have the license b...

5 Monate vor | 0

Beantwortet
Pixhawk Cube Orange AUX PWM Channels Not Activating When Using PX4 Toolbox (2023b)
There are no specific limiation of 4 uorb topics. It ideally depends on the algorithm you are designing in Simulink and the fla...

6 Monate vor | 0

Beantwortet
MATLAB getMATFilesFromPixhawk Function Fails to Retrieve SD Card Data from Pixhawk PID Controller Simulation
Based on the error message you are seeing, I don't think this is an issue with permission. The function getMATFilesFromPixhawk u...

6 Monate vor | 0

Beantwortet
how to deploy Control algorithm and Verify it in gazebo environment
I am glad to see that you used the custom uORB to do the debugging of your controller model. That is a good way. Another optio...

6 Monate vor | 1

Beantwortet
How to simulate my custom drone in jMAVSim with Matlab PX4 simulink ?
Based on my undertsanding the only difference is, from Simulink the SITL and jMAVSim are launched seperately. I am not sure how...

6 Monate vor | 1

| akzeptiert

Beantwortet
seek demo px4/PX4HITLSimulationFixedWingPlantSimulinkExample
This example ships with the 'UAV Toolbox Support Packge for PX4 Autopilots'. Ensure that you install this support package first....

6 Monate vor | 0

Beantwortet
The number of elements must be greater than zero
Ensure that you have built the PX4 Host Target using the hardware setup screens without errros. Once the build is successful, in...

6 Monate vor | 1

Beantwortet
Unable to complete PX4 support packages setup due to unresponsive firmware upload menu in Linux Ubuntu 22.04?
Which hardware you are using? What happens when you remove and reconnect the hardware when the hardware setupscreen becomes unr...

7 Monate vor | 0

Beantwortet
[SOLVED] UAV Toolbox Support Package can't detect WSL2
This looks like an issue that can be seen in Windows computer where the language is not English. To workaround this issue: Chan...

7 Monate vor | 1

| akzeptiert

Beantwortet
UAV Toolbox Support Package Alternative?
The R2024a release of UAV Toolbox Support Package for PX4 Autopilots now supports PX4 Firmware v1.14

8 Monate vor | 0

| akzeptiert

Beantwortet
The HITL example of UAV toolbox, there was a problem with QGC mission
Are you seeing any errors in the QGC or in NSH shell that why its disarming? without that it is bit difficult to understand what...

8 Monate vor | 0

Beantwortet
Error when run "Run quadcopter plant in normal simulation" in "Px4DemoHostTargetWithSimulinkPlant" example.
As the error clearly says the base sample time of the model you use is 0 and that cannot be supported in Nuttx. You need to make...

8 Monate vor | 0

Beantwortet
Use Multiple GPS in PX4 with PX4 supported package?
It is possible to use two GPS over serial connection. Most of the Pixhawk boards will have two GPS ports (GPS1 and GPS2) and it ...

8 Monate vor | 0

| akzeptiert

Beantwortet
How to locate the PX4 files which in wsl2 when I use the UAV ToolBox for PX4?
I believe the issue you might be facing is because of the distribution root folder name. The expected path is '\\wsl.localhost\U...

8 Monate vor | 0

| akzeptiert

Beantwortet
Questions about "UAV Toolbox Support Package for PX4 Autopilots" toolbox.
This means that the sensor modules are not publishing the corresponding uORB message. For example, Accelerometer block reads 's...

11 Monate vor | 0

Beantwortet
Building Cube Orange Model by Simulink
Other than the Cygwin toolchain and PX4 Firmware sources there are no additional dependencies required to deploy the code from S...

12 Monate vor | 0

Beantwortet
PX4 HIL with Pixhawk 6x with Monitor and Tune ERROR:Could not connect to target application: XCP internal error: timeout expired, in response to XCP CONNECT command
From the details provided, the serial port mapping you used, PX4 hardware connections, QGC parameters and the configuration sett...

etwa ein Jahr vor | 0

| akzeptiert

Beantwortet
PX4 SITL with Simulink based Plant Model
Depends on when the plant and controller start running there can be an offset between controller and plant. And as per the curre...

mehr als ein Jahr vor | 0

| akzeptiert

Beantwortet
Monitor and Tune PX4 Host Target Flight Controller with Simulink-Based Plant Model: Mismatched TCP Node
As per the documentation you need to run the Plant model first and then run the Controller model in another instance of MATLAB (...

mehr als ein Jahr vor | 0

Mehr laden