Error occurred while executing External Mode MEX-file 'ext_comm': Failed to connect to the target,

hi everyone.

when i'm upload my simulink model to c2000 F28379D its give error as follows,

Build process completed successfully

Output port 2 of 'C2000codePLL2017b_v2/Demux3' is not connected. [4 similar]

Component:Simulink | Category:Block warning

Unconnected line found in 'C2000codePLL2017b_v2' (outside of current view)

Component:Simulink | Category:Block diagram warning

Error occurred while executing External Mode MEX-file 'ext_comm': Failed to connect to the targetError occurred while executing External Mode MEX-file 'ext_comm': Failed to connect to the target. A time-out occurred while waiting for the connection response from the target. Possible reasons for the time-out:

a) The target is not switched on.

b) The target is not connected to your host machine.

c) The application for the model is not running on the target. You might have clicked the Stop button. If the Run button is not dimmed, click it. Otherwise, click the Build button, which downloads and runs your application on the target.

please help me to solve this error.

Thank you in advance

[SIVA KRISHNA]

Please recheck the Oscillator clock frequency properly. That should solve the issue. For F2838X devices, it should be 25 MHz.

[Ivana]

Hi! I also get the same error when the MPU6050 is connected to the the I2C_A of the C2000. When the SDA and SCL is connected to the GPIO 104 and 105. Please help me to solve this.

Answer 1

[anh tuan chu]

when i'm upload my simulink model to arduino mega2560 its give error as follows, Error occurred while executing External Mode MEX-file 'ext_comm

Failed to connect to the target. A time-out occurred while waiting for the connection response from the target. Possible reasons for the time-out:

a) The target is not switched on.

b) The target is not connected to your host machine.

c) The application for the model is not running on the target. You might have clicked the Stop button. If the Run button is not dimmed, click it. Otherwise, click the Build button, which

downloads and runs your application on the target.

[Do]

fix được không chỉ với e với ạ

[son]

mình cũng bị như này

[trinh cong thanh]

thật cảm giac

Answer 2

[Venkatesh Chilapur]

Please refer this post:

https://in.mathworks.com/matlabcentral/answers/306258-simulink-external-mode-not-working-on-texas-instruments-c2000-launchpad-f28377s

[dhanushka thennakoon]

Hi Venkatesh Chilapur

I set the settings according to your link.but after runnin same error shows.in I have set target settings port 2 and device manager also shows that my c2000 port is port2.what is the reason for this error and how to solve this,

error message is,

Build process completed successfully

Output port 2 of 'C2000codePLL2017b_v3/Demux3' is not connected. [4 similar]

Component:Simulink | Category:Block warning

Unconnected line found in 'C2000codePLL2017b_v3' (outside of current view) [2 similar]

Component:Simulink | Category:Block diagram warning

action: EXT_CONNECT

Component:Simulink | Category:Model

Error occurred while executing External Mode MEX-file 'ext_comm': Failed to connect to the target. A time-out occurred while waiting for the connection response from the target. Possible reasons for the time-out:

a) The target is not switched on.

b) The target is not connected to your host machine.

c) The application for the model is not running on the target. You might have clicked the Stop button. If the Run button is not dimmed, click it. Otherwise, click the Build button, which downloads and runs your application on the target.

Component:Simulink | Category:Block diagram error

Unable to connect to the 'TI Delfino F2837xD' target for 'C2000codePLL2017b_v3'.

Thank you in advance

[Venkatesh Chilapur]

Please connect to us at:

https://www.mathworks.com/support/contact_us.html

Answer 3

[AGORO SODIQ]

To correct this, Go to the Device Manager: Under the ports(COM &LPT) Uninstall the XDS100 Class Serial Port Driver.

Next, In the Texas Instrument Debug probes,

"Check" Load VCP for Auxiliary Port and

"Uncheck" Load VCP for Debug Probes.

Disconnect the DSP and reconnect it so that the drivers are installed again.

Make sure that when yu open the XDS100 Class USB serial Port again in device maneger you see:

Location: on XDS100 Auxiliary Port

Make sure other settings are correct: port setting, buad rate etc and you'll see it works

[Diaa Younes]

Thank you! This solved my issue