Beantwortet
Did anyone already use DMA with F28M36 ?
Please update on the version of MATLAB you are using?

mehr als 7 Jahre vor | 0

Beantwortet
ePWM setting for C2000 DSP, output not the right frequency
Hi Mike, Regarding your point of 'Also, if I look at ePWMA and ePWMB panes setting, is there a mistake for ePWMB output pane ...

mehr als 7 Jahre vor | 0

| akzeptiert

Beantwortet
ePWM setting for C2000 DSP, output not the right frequency
Please share your model and provide MATLAB version details, and Hardware version details for further investigation.

mehr als 7 Jahre vor | 0

Beantwortet
Simulink compilation error: Launchpad F28069M
Looks like your model is stuck in external mode configuration which happens to be a intermediate config set that is used in back...

mehr als 7 Jahre vor | 1

| akzeptiert

Beantwortet
How do I generate complementary signals on ePWMA and ePWMB with F28335 using Simulink ePWM block?
Please mention the version of the MATLAB and version of the C2000 hardware support package that you are working with.

mehr als 7 Jahre vor | 0

Beantwortet
The Embedded Coder for the TI c2000 F2837xD builds and compiles but does not deploy to hardware only when some blocks are used?
Please refer the link: https://in.mathworks.com/matlabcentral/answers/358275-how-to-create-and-open-a-code-composer-studio-ccs-...

mehr als 7 Jahre vor | 0

Beantwortet
The Embedded Coder for the TI c2000 F2837xD builds and compiles but does not deploy to hardware only when some blocks are used?
I think the log you have attached is quite normal. After the programming is running from target, it is a standalone application ...

mehr als 7 Jahre vor | 0

Beantwortet
Usage of C2000 TI family launch pad F28069M without Embedded coder
Yes, you can generate code from Simulink coder/Matlab coder and work with C2000 target. But Embedded coder provides more option ...

mehr als 7 Jahre vor | 0

Beantwortet
How to measure task execution time on F28379D target?
This feature is not supported in MATLAB 2016b. Please consider upgrade to 2017a or later where this feature is introduced.

mehr als 7 Jahre vor | 0

Beantwortet
How to measure task execution time on F28379D target?
Please mention the MATLAB version and attach the Model file if possible.

mehr als 7 Jahre vor | 0

Beantwortet
I am trying to generate PWM for F28335 with CCSV6 with simulink coder. C code is generated when I am trying to "Deploy to Hardware" an error occurred. The diagnostic report is attached.
Hi, Run the 'targetupdater' and complete the hardware setup once. You could also provide the details of the path of tools th...

mehr als 7 Jahre vor | 0

Beantwortet
Problem in programming 28379D from Simulink
Hi, Please try to connect to board from CCS and see if you are successful. Do you see the device listed under device manager?...

mehr als 7 Jahre vor | 1

Beantwortet
Code generated by Simulink Embedded Coder runs slower as more coded added, why?
Hi, If the execution time is larger than the sample time, we are in an overrun situation. We want to keep the execution time ...

mehr als 7 Jahre vor | 0

Beantwortet
Program the TI F28335 for CAN communication
Hi, Please update on the MATLAB version being used. Regards, Venkatesh C

mehr als 7 Jahre vor | 0

Beantwortet
How to enable the MCU's internal pullup/pulldown resistors at Embedded Coder Support Package for Texas Instruments C2000 Processors?
Hi Gabriel, There is no Pulldown circuit. You need to add an external one if required. If pullup is disabled, the pin would b...

mehr als 7 Jahre vor | 0

Beantwortet
How to enable the MCU's internal pullup/pulldown resistors at Embedded Coder Support Package for Texas Instruments C2000 Processors?
HI, If you can try the following: Please use the "System Initialize" block found under "Simulink coder->Custom Code" lib...

mehr als 7 Jahre vor | 0

| akzeptiert

Beantwortet
Problem with TI TMDSHVMTRINSPIN+F x hardware (C2000 processors)
Hi Galo, Your approach should work considering the fact that both Kits are the same with only a subtle difference that the 'T...

mehr als 7 Jahre vor | 0

Beantwortet
LaunchXL-F28379D in External Mode. I only got last few values when I save a signal "To Workspace", any idea of the reason?
Hi Josep, Use a hardware trigger for ADC conversion and see if it helps. I have model attached in which I am triggering ADC ...

fast 8 Jahre vor | 0

Beantwortet
I cannot find c2000 as well as target preferences in embeded coder in matlab 2016a?is it there or c5000 is only there?
Please try this one: https://www.mathworks.com/help/supportpkg/texasinstrumentsc2000/ug/install-support-for-c2000-processors....

fast 8 Jahre vor | 0

Beantwortet
With 28335 TI, embedded coder, for a sine signal with and without presence of ADC block frequency is changing
The likely reason for this is overrun issue of the step function. You may consider reducing the sample time of the step functio...

fast 8 Jahre vor | 0

Beantwortet
With 28335 TI, embedded coder, for a sine signal with and without presence of ADC block frequency is changing
Hi, Please send us the model. Regards, Venkatesh C

fast 8 Jahre vor | 0

Beantwortet
Simulink CAN timeout on embedded coder
You can create a counter and reset it when you get a CAN message (from the function call of the CAN block or an interrupt). If t...

fast 8 Jahre vor | 0

Beantwortet
the third party installation package got skipped while installing Add ons.
You can ignore the warning for now and start using the support package. Please update for any issues encountered during the time...

fast 8 Jahre vor | 0

Beantwortet
CCS/F28M36P63C2: Can't compile an auto generated code from Simulink.
https://www.mathworks.com/matlabcentral/answers/382607-ccs7-unsupported-by-matlab-simulink

fast 8 Jahre vor | 0

| akzeptiert

Beantwortet
Simulink model doesn't look configured for the Texas Instruments' F28379D processor
Make sure to select the System Target file as ert.tlc under code generation pane.

fast 8 Jahre vor | 0

| akzeptiert

Beantwortet
Cant get complete adc data using c2000 in external mode
Please run through TASK 3 from link below and see if it helps: https://www.mathworks.com/help/supportpkg/texasinstrumentsc2000/...

fast 8 Jahre vor | 0

Beantwortet
CCS7 unsupported by Matlab/Simulink ?
Could you please update on the version of the support package? 17.2.2 is latest, please let us know which version is installed ...

fast 8 Jahre vor | 0

Beantwortet
How can I call assembler code DSP28x_usDelay() in a simulink model
Please use Atomic subsystem and place the customer code block from Simulink coder -> custom code -> system outputs. double click...

fast 8 Jahre vor | 0

| akzeptiert

Beantwortet
CCS/F28M36P63C2: Can't compile an auto generated code from Simulink.
Please ensure you have latest version of the hardware support package installed - 17.2.2 This can verified by clicking - Add-On...

fast 8 Jahre vor | 0

Beantwortet
CCS/F28M36P63C2: Can't compile an auto generated code from Simulink.
Hi, Did you try to launch the project from diagnostic viewer from MATLAB. We support automatic project creation in CCS from M...

fast 8 Jahre vor | 0