Beantwortet
axial flux permanent magnet generator
The FEM-Parametrized PMSM block can be parametrized with data from FEM tools to simulate an axial flux machine. Check this exam...

10 Monate vor | 0

Beantwortet
using spice models in simlink
Simscape Electrical is posible to convert SPICE subcircuit to custom Simscape components using subcircuit2ssc function. https:/...

10 Monate vor | 0

Beantwortet
how trigger timer circuit 555
Simscape Electrical has an example that shows a pulse-width-modulated (PWM) output implemented using a 555 Timer in astable mode...

10 Monate vor | 0

Beantwortet
How to give a constant delay to variable duty cycle pulse
In Simscape Electrical this is possible using two approaches: using the On-Off Delay block: https://mathworks.com/help/sps/ref/...

10 Monate vor | 0

Beantwortet
what type of kalman filter algorithm is applied to the control of pressure process??can anyone help me out please??
If we can reduce the model of the system to a linear state-space model we can use the standard Kalman filter. If the model is no...

10 Monate vor | 0

Beantwortet
How to change the value to irradiance block from workspace ? in simelectronices
The Solar Cell has an input Ir for irradiance. This input can be changed during runtime using a simulink signal and and S-PS Con...

10 Monate vor | 0

Beantwortet
SimElectronics
Most likely product not installed and therefore the block can not be found under the path.

10 Monate vor | 0

Beantwortet
Nonlinear Circuit Simulation
Simscape Electrical (formerly SimPowerSystems and SimElectronics) provides a variety of different levels of fidelity, including...

10 Monate vor | 0

Beantwortet
[Simulink][To Previous Version][Error]
The name and appearance may look the same. However, the actual path might have changed between releases. Simscape Electrical eme...

11 Monate vor | 0

Beantwortet
.My academic project is with Multilevel inverter...I am trying to supply the input DC with photovoltaic cell...I am trying to construct a Photovoltaic module...I am trying to measure the current across a single solar cell...I am facing a pr
Each physical network represented by a connected Simscape™ block diagram requires solver settings information for simulation. Th...

11 Monate vor | 0

Beantwortet
I am getting error in results while using my simulink PMSM model
The model runs in variable-step, but the maximum step size is not small enough to capture the AC quantities. By setting the Max ...

11 Monate vor | 0

Beantwortet
How to remove generators from matpower
MATPOWER is not developed by MathWorks. It is best to consult the documentation of this third party tool or contact its develope...

11 Monate vor | 0

Beantwortet
I am getting wrong value for Power calculation
It appears that the wrong block is used to compute the power. Power (Phasor) will compute active and reactive powers using volta...

11 Monate vor | 0

Beantwortet
PWM signal goes to zero when using PID controller after MPPT (P&O) in PV system
Most likely the output of the PID controller is <=0 which will result in PWM signal to be 0. Double check the corectnes of the c...

11 Monate vor | 0

Beantwortet
how to solve this problem
Without a model is not possible to point to the root cause but the problem is, as the error points out, the control port of a mu...

11 Monate vor | 0

Beantwortet
Cannot connect Battery to Servomotor
Try using blocks from the same technology. In Simscape Electrical there are two technologoies, Simscape and Specialized Power Sy...

11 Monate vor | 0

Beantwortet
implementing a two-loop PI controller for both current and voltage - buck converter
There are many relevant examples in Simscape Electrical to start with. Check out this bidirectional DC-DC converter current cont...

11 Monate vor | 0

Beantwortet
implement a photovoltaic generator of energy in Simulink/matlab
Simscape Electrical has an example that shows the design of a stand-alone solar photovoltaic (PV) DC power system with battery b...

11 Monate vor | 0

Beantwortet
Connect MATPOWER with Simulink model
MATPOWER is not developed by MathWorks. Probably best to check the documentation for this 3rd party tool.

11 Monate vor | 0

Beantwortet
how to use MATPOWER for opf in case6
MATPOWER is not developed by MathWorks. Probably best to check the documentation for this 3rd party tool.

11 Monate vor | 0

Beantwortet
How to open the electrical switch again after it closed
You can use a Pulse Generator block to control the switch: https://mathworks.com/help/simulink/slref/pulsegenerator.html You ca...

11 Monate vor | 0

Beantwortet
Battery charging through PMSG while rotor of PMSG rotate with pedal of bike
A good place to start is this example: https://mathworks.com/help/sps/ug/pm-generator-for-battery-charging.html This example sh...

11 Monate vor | 0

Beantwortet
PMLSM force and back-EMF constant
The back EMF constant is the peak voltage induced by the permanent magnet in the per-unit rotational speed of each of the phases...

11 Monate vor | 0

Beantwortet
matpower8.0 comes with most test failed
MATHPOWER is not developed by MathWorks. Would be more suitable to get in touch directly with the developers of this 3rd party t...

12 Monate vor | 0

Beantwortet
Simscape Bidirectional DC-DC Converter: Gate Control Input Type and Parameter Calculation Issues
With the Bidirectional DC-DC Converter, input G is always a vector. In the nonisolated variant we have two switches and therefor...

12 Monate vor | 0

Beantwortet
How to compute dq current in a delta-wound motor?
From the control design point of view there is no difference between wye or delta windings. However, some inputs required by the...

12 Monate vor | 0

| akzeptiert

Beantwortet
vector control synchronous machine Simulink
Simscape Electrical has an example showing how to control the torque in an externally excited synchronous motor (SM) drive by us...

etwa ein Jahr vor | 1

Beantwortet
Question about the OCV of Fuel cell block example from ee lib
This behaviour is because we are changing the pressure of fuel from 2.5 to 5 bar. By increasing the pressure this will increase ...

etwa ein Jahr vor | 0

Beantwortet
Can the Motor & Drive (System Level) Simscape Electrical block be used to model an BLDC + Inverter power generator?
The Motor & Drive (System Level) block can operate in four quadrants and you can simulate the behaviour of a BLDC drive. Specify...

etwa ein Jahr vor | 0

Beantwortet
Best practice for setting Simulink block parameters at initialization?
If you want easily to switch the system, I will probably use variants. Check out this example as a starting point: https://math...

etwa ein Jahr vor | 0

| akzeptiert