photo

Matthew Mishrikey


Last seen: 28 Tage vor Aktiv seit 2021

Followers: 0   Following: 0

Statistik

MATLAB Answers

17 Fragen
7 Antworten

RANG
5.641
of 297.457

REPUTATION
8

BEITRÄGE
17 Fragen
7 Antworten

ANTWORTZUSTIMMUNG
58.82%

ERHALTENE STIMMEN
2

RANG
 of 20.438

REPUTATION
N/A

DURCHSCHNITTLICHE BEWERTUNG
0.00

BEITRÄGE
0 Dateien

DOWNLOADS
0

ALL TIME DOWNLOADS
0

RANG

of 158.938

BEITRÄGE
0 Probleme
0 Lösungen

PUNKTESTAND
0

ANZAHL DER ABZEICHEN
0

BEITRÄGE
0 Beiträge

BEITRÄGE
0 Öffentlich Kanäle

DURCHSCHNITTLICHE BEWERTUNG

BEITRÄGE
0 Highlights

DURCHSCHNITTLICHE ANZAHL DER LIKES

  • Thankful Level 3
  • Knowledgeable Level 1
  • First Answer

Abzeichen anzeigen

Feeds

Anzeigen nach

Frage


Simulink scope trace is grayed out
In simulink I have a scope with three inputs. The scope has 3 subplots. The first and third input have a mux in front, and ...

29 Tage vor | 0 Antworten | 0

0

Antworten

Frage


Run an enabled and triggered subsystem only one time (single shot)
I have a Simulink enabled and triggered subsystem that I want to execute only one time. I think one way to do it is to make ...

etwa ein Monat vor | 1 Antwort | 0

1

Antwort

Frage


Simulink dashboard button matching
I'm looking for suggestions on how to approach a Simulink interface problem. In case 1 below, both dashboard buttons have con...

etwa 2 Monate vor | 1 Antwort | 0

1

Antwort

Frage


A few basic Simulink/Simscape questions
In the past I've generally used Simulink simulations for short bursts of transient analysis. I was curious if it were possibl...

etwa 2 Monate vor | 1 Antwort | 0

1

Antwort

Frage


Dynamic dashboard radio button options
Hello! I was curious if it was possible to make the options of a radio button change based on another radio button. This is ...

etwa 2 Monate vor | 2 Antworten | 0

2

Antworten

Frage


variables with scope local to subsystem
I'm a bit confused about variable scope. I think I know what's going on but am looking for confirmation and maybe advice on th...

etwa 3 Jahre vor | 1 Antwort | 0

1

Antwort

Beantwortet
Radio Button Mask for Simscape Block
I figured out a way. I saw a snippet of code in one of the videos on the topic, and it gave me enough clues to write a callback...

etwa 3 Jahre vor | 0

| akzeptiert

Frage


Radio Button Mask for Simscape Block
I have a stock Simscape block (Cauer Element) that has two parameters - Resistance and Tau. I am trying to add a mask to modify...

etwa 3 Jahre vor | 1 Antwort | 0

1

Antwort

Frage


get_param fails with simscape block
Weird/unexpected behavior, not sure if it's a bug. I'm trying to use get_param to access a stock simscape thermal component. I...

etwa 3 Jahre vor | 1 Antwort | 0

1

Antwort

Beantwortet
Basic Slider Switch question
I think I figured out a way. I hope there's a better solution because this seems like a royal pain. 1) in the simscape compone...

etwa 3 Jahre vor | 0

Beantwortet
Basic Slider Switch question
I think I'm getting closer to an answer here. I setup slider switch to control a constant block, which feeds a data store wri...

etwa 3 Jahre vor | 0

Frage


Simscape Block Parameter not Tunable
I wish to control a Simscape block parameter using the dashboard slider switch. I select Temperature Source, but the slider swi...

etwa 3 Jahre vor | 1 Antwort | 0

1

Antwort

Frage


Simulink dashboard switch to control masked parameter
I wanted to have a slider switch control such that On position would make it 1 Ohm and off position would make it 5 ohms. The s...

etwa 3 Jahre vor | 1 Antwort | 0

1

Antwort

Beantwortet
Two circles geometry problems
Not clear from the second drawing what the dl of interest is. Let's assume dl is the distance between the left edge of each ci...

etwa 3 Jahre vor | 0

| akzeptiert

Beantwortet
Control Design Onramp with Simulink
Enter learning.simulink.launchOnramp('controls') in your MATLAB window.

etwa 3 Jahre vor | 2

Frage


Parameter Writer block not recognizing blocks
In image below I show a sim with a slider switch that modifies the constant block on the left. This the uses a goto/from block ...

etwa 3 Jahre vor | 1 Antwort | 0

1

Antwort

Beantwortet
Is there a way to nest transfer functions?
Okay, nevermind, found the solution is to use s = tf('s') rather than tf([num dem]).

etwa 3 Jahre vor | 0

| akzeptiert

Frage


Is there a way to nest transfer functions?
I wish to build up a transfer function inside a for loop such that each iteration builds up a new transfer function based on pre...

etwa 3 Jahre vor | 1 Antwort | 0

1

Antwort

Frage


Basic Slider Switch question
I was curious if it was possible to make a slider switch dashboard element control more than one block simultaneously. Alterna...

etwa 3 Jahre vor | 3 Antworten | 0

3

Antworten

Beantwortet
Simscape/Simulink persistent variable in algebraic loop
I think I managed to figure out a solution. As suggested elsewhere a delay block can "break" the algebraic loop. I needed thr...

etwa 3 Jahre vor | 0

| akzeptiert

Frage


Simscape/Simulink persistent variable in algebraic loop
I have a simple Simscape electrical model containg a circuit that trips if a current is exceeded. I want the trip to happen a c...

etwa 3 Jahre vor | 2 Antworten | 0

2

Antworten

Frage


Generate Zth transient thermal impedance curves with Simscape
Simscape has some nice thermal domain elements like Cauer thermal model elements. I was looking to generate a set of Zth curves...

mehr als 3 Jahre vor | 1 Antwort | 0

1

Antwort

Frage


Trying to convert Kelvin to Celsius in Simscape code
I have a simulation with some Simscape Thermal and Electrical elements. The electrical element is a modification of the stock t...

mehr als 3 Jahre vor | 1 Antwort | 0

1

Antwort

Frage


simscape block node arrangement
In the IGBT example here: https://www.mathworks.com/help/physmod/sps/ug/Troubleshoot-of-spice-nigbt-conversion.html the gener...

mehr als 3 Jahre vor | 1 Antwort | 0

1

Antwort