Statistik
RANG
226.744
of 300.781
REPUTATION
0
ANTWORTZUSTIMMUNG
0.0%
ERHALTENE STIMMEN
0
RANG
of 21.088
REPUTATION
N/A
DURCHSCHNITTLICHE BEWERTUNG
0.00
BEITRÄGE
0 Dateien
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANG
of 171.031
BEITRÄGE
0 Probleme
0 Lösungen
PUNKTESTAND
0
ANZAHL DER ABZEICHEN
0
BEITRÄGE
0 Beiträge
BEITRÄGE
0 Öffentlich Kanäle
DURCHSCHNITTLICHE BEWERTUNG
BEITRÄGE
0 Discussions
DURCHSCHNITTLICHE ANZAHL DER LIKES
Feeds
Can't set capacitor initial voltage of cap because of powergui error
Hi Shashwat, Thanks for your comment. I have tried the steps in the shared link. But it did not work. So, I have attached my ...
etwa 6 Jahre vor | 0
Frage
Unable to initialise capacitor voltage
Hello, I have a very simple circuit taken from simscape library in simulink. My circuit is made of a definite gain opamp, a ca...
etwa 6 Jahre vor | 1 Antwort | 0
1
Antworthow to resolve the 'dot indexing not supported for this type of variable' error when creating GUIs with GUIDE?
I got a similar error of Dot indexing. But unable to find loop where the error exists :( I have attached a pic that tells about ...
etwa 6 Jahre vor | 0
Too many output arguments in 'project' command :(
Yes, I have to define a function to use it. Thanks for your comments :)
mehr als 7 Jahre vor | 0
Frage
Too many output arguments in 'project' command :(
Hey i just try to do Xproj = project(Xm, Wpca(:,1:2)) where Xm & Wpca are 178*13 double type vectors. I get error 'Too...
mehr als 7 Jahre vor | 1 Antwort | 0
1
AntwortNeed to find the distribution from mean & standard deviation
Thank you all for your answers. Finally, I managed to tune something near to the desired mean & std. Yes, I was looking for the ...
mehr als 7 Jahre vor | 0
Frage
Need to find the distribution from mean & standard deviation
Hello, I need a 100 numbers of distribution for a specified mean & std. I found one, but its not accurate. The one I found is...
mehr als 7 Jahre vor | 3 Antworten | 0
3
AntwortenFrage
Single sided amplitude FFT
For a normal FFT analysis, I can do directly from the scope. But how to do for a single-sided amplitude FFT directly in simulink...
mehr als 10 Jahre vor | 0 Antworten | 0
0
AntwortenPlot single-sided amplitude spectrum.
hey, can a single sided FFT taken directly from the scope by using an absolute block before the scope ?
mehr als 10 Jahre vor | 0
Frage
PI controller and an integrator.
Hi, I am using a discrete control algorithm to control an inverter. In this I have to construct a PI controller and an integr...
mehr als 10 Jahre vor | 0 Antworten | 0
0
AntwortenHaving a Simulink error while simulating a UAV to track a UGV.
hey I have the same problem. I n my case the feedback is a single number and when I put an unit delay, it converts to 3 numbers...
mehr als 10 Jahre vor | 0
An error in the sum of three signal
Seems adding a memory makes more complications, which I have attached in the picture. And there are many unit delay blocks. Whic...
fast 11 Jahre vor | 0
An error in the sum of three signal
<</matlabcentral/answers/uploaded_files/24948/Capture.JPG>>
fast 11 Jahre vor | 0
Frage
An error in the sum of three signal
I just use sum of three signals and i get an error like this. Can you help to rectify this error ?
fast 11 Jahre vor | 3 Antworten | 0
3
AntwortenFrage
Pulse generation from duty cycles in Space vector modulation
hi, I have duty cycle values d1, d2 & d3 for a 3 level Neutral Point Converter. Now how to generate 12 pulses for it using th...
etwa 12 Jahre vor | 1 Antwort | 0
1
AntwortFrage
How to clear this Error :In an assignment A(I) = B, the number of elements in B and I must be the same
In the below hexagon figure, the parallelogram of coordinate (g,h) is the base plane on which I am working on. In this plane ...
etwa 12 Jahre vor | 0 Antworten | 0
0
AntwortenFrage
In an assignment A(I) = B, the number of elements in B and I must be the same
I have written a simple Matlab s-function program to calculate nearest coordinates in a parallelogram, . the code is as follows:...
etwa 12 Jahre vor | 0 Antworten | 0
0
AntwortenIn an assignment A(I) = B, the number of elements in B and I must be the same.
I too get the same error.I have written a simple Matlab s-function program to calculate nearest coordinates in a parallelogram, ...
etwa 12 Jahre vor | 0
