photo

Jason R


Aktiv seit 2014

Followers: 0   Following: 0

Nachricht

Statistik

All
  • Knowledgeable Level 2
  • First Answer
  • Solver

Abzeichen anzeigen

Feeds

Anzeigen nach

Gelöst


Use a timetable to analyze a train timetable (Part 5)
You are analyzing a train timetable (you have some time to kill since you just missed your train!) How many trains depart each d...

fast 8 Jahre vor

Gelöst


Use a timetable to analyze a train timetable (Part 4)
You are analyzing a train timetable (you have some time to kill since you just missed your train!) What is the average daily tri...

fast 8 Jahre vor

Gelöst


Use a timetable to analyze a train timetable (Part 3)
Oh no, you missed your train to Boston (again?)! How many times can you miss that train today? (In other words, how many Boston ...

fast 8 Jahre vor

Gelöst


Use a timetable to analyze a train timetable (Part 2)
Oh no, you missed your train to Boston! Find the departure time of the next available train by analyzing the train timetable. Yo...

fast 8 Jahre vor

Gelöst


Use a timetable to analyze a train timetable (Part 1)
Oh no, you missed your train to Boston! Find the departure time of the next available train by analyzing the train timetable. Th...

fast 8 Jahre vor

Gelöst


Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

etwa 9 Jahre vor

Gelöst


Determine if input is odd
Given the input n, return true if n is odd or false if n is even.

etwa 9 Jahre vor

Gelöst


Add damping to a mass spring system
Model an ideal mass-spring-damper system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/im...

etwa 9 Jahre vor

Gelöst


Model a mass spring system
Model an ideal mass-spring system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/images/se...

etwa 9 Jahre vor

Gelöst


Model a falling body
An object is falling freely from a height of 22 meters under the force of gravity. <<http://blogs.mathworks.com/images/seth/c...

etwa 9 Jahre vor

Gelöst


Make a half wave rectifier
Produce a signal that outputs the given sine wave source when it is greater than zero and outputs zero when it is less than zero...

etwa 9 Jahre vor

Gelöst


Make a full wave rectifier
Produce a full wave rectifier waveform for the given sine wave source. For a sine wave input, the output of the full wave rec...

etwa 9 Jahre vor

Gelöst


Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>

etwa 9 Jahre vor

Gelöst


Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...

etwa 9 Jahre vor

Gelöst


Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...

etwa 9 Jahre vor

Gelöst


Produce a Fibonacci sequence
Construct a diagram that generates the Fibonacci sequence: 1, 1, 2, 3, 5, 8, 13, 21, 34.....up to 377 The Fibonacci sequ...

etwa 9 Jahre vor

Gelöst


Model a simple pendulum
Model a simple pendulum of length 200cm with bob of mass 100g and plot the position in degrees. The pendulum starts at 30 degree...

etwa 9 Jahre vor

Gelöst


Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...

etwa 9 Jahre vor

Gelöst


Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...

mehr als 9 Jahre vor

Gelöst


Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...

mehr als 9 Jahre vor

Gelöst


Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>

mehr als 9 Jahre vor

Gelöst


Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...

mehr als 9 Jahre vor

Beantwortet
How can I plot a root locus for an open loop system?
To find the root locus of G=1/(10s+5), use the following code: s=tf('s'); G=tf(1/(10*s+5)); rlocus(G) This should be eno...

fast 10 Jahre vor | 0

| akzeptiert

Beantwortet
please I wrote this code to solve an equation of linear systems using LU factorization but it keeps giving me zeros as the value of x. please can someone help? thanks in advance
It seems that you initialize y as a vector of zeros (y = zeros (n,1);) and then use y to solve for b(n) and b(j) without updatin...

mehr als 10 Jahre vor | 0

Gelöst


Add two numbers
Given a and b, return the sum a+b in c.

mehr als 10 Jahre vor

Gelöst


Find the sum of all the numbers of the input vector
Find the sum of all the numbers of the input vector x. Examples: Input x = [1 2 3 5] Output y is 11 Input x ...

mehr als 10 Jahre vor

Gelöst


Make the vector [1 2 3 4 5 6 7 8 9 10]
In MATLAB, you create a vector by enclosing the elements in square brackets like so: x = [1 2 3 4] Commas are optional, s...

mehr als 10 Jahre vor

Beantwortet
Can you create a plot with contourf without the contour lines?
Use the shading flat command. Example use: Z = peaks(20); contourf(Z,10); shading flat

fast 11 Jahre vor | 0

Beantwortet
please please ...... i need help in this programme is there an error
What is the problem? I was able to run your code when I uncommented the variables k, v, etc. Remember that anything after a % wi...

fast 11 Jahre vor | 0

| akzeptiert

Beantwortet
how to silence display of variables?
Use ; to suppress output. So, Y(i)=0*X(i)+0; instead of Y(i)=0*X(i)+0,

fast 11 Jahre vor | 1

| akzeptiert

Mehr laden