Beantwortet
How to a create a label at the bottom of a vertical line?
Like this? x = linspace(0,6,100); y = exp(x); plot(x,y) xline(4.5,'-',{'Acceptable','Limit'}, 'LabelVerticalAlignment', 'bot...

9 Monate vor | 0

| akzeptiert

Beantwortet
Secant method Nan Error
You haven't updated error in your while loop. Try including something like error = abs(X0-X1);

9 Monate vor | 0

| akzeptiert

Beantwortet
Function error in ODEs RK4 method, solving 6 unknowns
It works for me (I've commented out the fprint statements in the code below - but it works with them in!): global CDin psi thet...

9 Monate vor | 0

| akzeptiert

Beantwortet
I keep getting the error using '/'.
Try mu_ratio=(1-(vol_frac(c,1)/0.605).*((particle_ratio(c,1)).^1.2)).^(-1.5125); Notice the dots! .* .^ Difficult to be...

9 Monate vor | 0

Beantwortet
Plateau followed by one phase decay
Like this? x = 0:0.5:20; % time in seconds Y0 = -0.6; % signal baseline value Plateau = -1; % singnal plateu after trigger/st...

9 Monate vor | 1

Beantwortet
Radiation view factor using Monte Carlo
I think you probably need cos(theta), rather than theta, to be linearly spaced.

10 Monate vor | 0

Beantwortet
How to fix a syntax in the oscillator's plot code?
Like this (both x_1 and x_2 are contained in y) T0 = 10; omega0 = 1; M = 1; F = 1; x_1 = 0; x_2 = 0; x_0 = [x_1 x_2]; ts...

10 Monate vor | 0

| akzeptiert

Beantwortet
ODE45has long runtime and graph will not plot
Here's my attempt to make sense of your equations tauspan = 0:100:10000; % p0 = [0.5 0.5 0 0]; % dp1dt = -rf + rr % dp2...

10 Monate vor | 0

Beantwortet
Two graphs in the same plot, why?
Something like this data = xlsread('sunHoursInTrollhattan.xlsx'); mins = data(:,1)*60 + data(:,2); plot(1:12, mins,'o'),grid ...

10 Monate vor | 0

| akzeptiert

Beantwortet
Two graphs in the same plot, why?
You have the hours as one plot and the minutes as the other! Turn the data into all minutes, or all hours first.

10 Monate vor | 0

Beantwortet
Could anyone help me in fixing the problem in my code for solving the initial value problem numerically: y'=y^2, y(0)=1?
Here's an attempt using fminsearch. I don't know anything about the Obreschkoff method, so couldn't say if your equations are...

10 Monate vor | 0

| akzeptiert

Beantwortet
I get this message(Attempted to access F(5); index out of bounds because numel(F)=4.) when I run the code below..
In fsode you try to use F(7) when calculating F(5), before you have calculated F(7)!

10 Monate vor | 1

| akzeptiert

Beantwortet
Laser Rate Equation Modelling
Like this? (Look at lines 27, 28 and 38) %Script % Define model parameters temperature = 25; wavelength = 1.312e...

10 Monate vor | 0

Beantwortet
Determine the coordinates of the nodes forming the outermost circle
Here's an alternative way: nodes = importdata("nodes.mat"); figure plot3(nodes(:,1),nodes(:,2),nodes(:,3),'b.','Markersize',1...

11 Monate vor | 0

Beantwortet
Problem with fitting a loglog plot
polyfit doesn't like the log of zero. One option is to remove the first row of the data: data_exp_high = load("data_Q_1e-8.txt...

11 Monate vor | 0

Beantwortet
Index in position 2 exceeds array bounds (Index must not exceed 1) errors?
N0 is a 4x1 vector, but you call it with two indices in the for loop! Turn N(1,j) into N(1) and similarly for the other calls t...

11 Monate vor | 0

| akzeptiert

Beantwortet
How do I solve this ODE system where there exists derivatives in both sides?
You can separate the terms as follows:

11 Monate vor | 0

Beantwortet
why am i getting grey figure box can someone fix please
Making some assumptions about your function pendulumODE, I think the following is more like what you expect to see: % Constants...

11 Monate vor | 0

Beantwortet
Algae growing, concentration curve problem
Increase nt to 10000 and it works just fine for T = 20000.

11 Monate vor | 0

Beantwortet
Error ''Array indices must be positive integers or logical values.'' when putting interval of 0.01 in a for loop
More like this: k = 0:0.1:2; n = numel(k); for i = 1:n x(i) = k(i); y(i) = k(i)*k(i) + 3*k(i) - 4; end plot(x,y...

11 Monate vor | 0

Beantwortet
Trying to code from Polymath
Like this for example (I'll leave you to extract the numerical values): Wspan = [0 2]; % Integration range % Initial valu...

11 Monate vor | 0

Beantwortet
Unable to solve differential equation with finite difference method
Should be more like this I think: b = 0.02; m = 80; L = 0.7; g = 9.81; J = m * L^2/3; a = 0; bet = 2; alpha = 0; beta = 3...

12 Monate vor | 0

Beantwortet
FDM using succsesive overrelaxation method,
For w1 and T1 you have w1(:,Nx1+1) = (((la*B1*dx1)/(dx2*A1))*(w2(:,2)-w2(:,1)))+w1(:,Nx1); %Continuity of shear stress ...

12 Monate vor | 0

Beantwortet
Solving first order ODE with initial conditions and symbolic function
You can do it numerically as follows: % input parameters Tinf=70+273.15; Ti=20+273.15; d=15e-2; r=d/2; cdepth=10/1100; Tf...

etwa ein Jahr vor | 0

Beantwortet
can someone help me to analyze this program? How does the flowchart look like?
Perhaps this will help: %radiasi benda hitam % constants h=6.626e-34; c=3e8; k=1.38066e-23; % range of values lambda ...

etwa ein Jahr vor | 0

Beantwortet
Error using surf (line 71) Data dimensions must agree
More like this? for it=1:2 for jt=1:3 zt(it,jt)=it+(jt-1); end end [x,y] = meshgrid(1:3,1:2); figure; surf(x...

etwa ein Jahr vor | 1

Beantwortet
How to find Basins of attraction for the Halley method?
Don'tforget the dot multiply: f = @(z) z.^3 +1; df = @(z) 3*z.^2; ddf=@(z) 6*z; % its roots r1 = -1; r2 = 1/2 + 1i*...

etwa ein Jahr vor | 0

| akzeptiert

Beantwortet
"Invalid use of operator." doesn't go even after trying various solutions :(
Why nor just use Matlab's inbuilt cart2pol function?

etwa ein Jahr vor | 0

Beantwortet
Heat equation using Boundary condition
function statements of this form (i.e. functions eq1, initial and ba) need to go at the end of the script, not the start.

etwa ein Jahr vor | 0

Beantwortet
A for loop that will run until a specific mathematical value is found
You could try replacing the "for i = 2:10 " loop by something like nports = 1; while Q(i)<Qdesired nports = nports ...

etwa ein Jahr vor | 0

| akzeptiert

Mehr laden