photo

Mohsen Aleenejad

Last seen: ein Tag vor |  Aktiv seit 2020

Followers: 1   Following: 0

Nachricht

Statistik

  • Knowledgeable Level 2
  • First Review
  • First Answer
  • Revival Level 1

Abzeichen anzeigen

Feeds

Anzeigen nach

Beantwortet
Reduce noise of Te signal in a Induction machine
This issue seems more of a control issue rather than noise, I think these torque ripples might be comming from some modeling ina...

etwa ein Jahr vor | 0

Beantwortet
Thermal insulation with phase change materials on simscape
Have you seen this example: https://www.mathworks.com/matlabcentral/answers/1903145-how-to-model-a-phase-change-stefan-problem-...

etwa ein Jahr vor | 0

Beantwortet
Physical model of computer
I'm curious why you you would get 50 before Reconduction_CasetoJunction but 40.28 after that on the riht side! I wanna know what...

etwa ein Jahr vor | 0

Beantwortet
SimPowerElectronicsのブロックを改造してダイオードと素子の電流を出力する改造を施した際に保存できないエラーを解除する方法
Hi, I have done the same modifications on my side, and it did not throw any errors. I just simply unlink this block from he l...

fast 2 Jahre vor | 0

Beantwortet
실행할 입력 인수가 추가적으로 필요합니다. 무엇을 넣어야 하나요? Additional input arguments are required to run. What should I put in?
Hi, When you run the MATLAB script with: function x = key2note(A, keynum, dur, fs) tt = 0:(1/fs):dur-1/fs; freq = 440 * 2^(...

fast 2 Jahre vor | 0

Beantwortet
Does changing the phase of the variable phase shifter in MATLAB Simulink causes the amplitude of the continuous wave to change as well?
Hi, If by continuous wave, you mean "I", then, answer is yes. However, it makes more sense that the amplitude is sqrt(I^2+Q^2) ...

fast 2 Jahre vor | 0

Beantwortet
Further understanding into Hall Validity & Hall Decoder block
How accurate is the 'Hall Validity' block in validifying the Hall sensor? The Hall Validity block works on every Hall ...

etwa 2 Jahre vor | 0

Beantwortet
Turn-on of the N-channel IGBT
Are you sure those parameters in the N-Channel IGBT were set properly? This happens due to the parameters you set for your IGB...

etwa 2 Jahre vor | 0

Beantwortet
Further understanding into Hall Validity & Hall Decoder block
Hi Alex, 1-If you search for "Hall Validity" or "Hall Decoder" into MATLAB search bar, you'll find all of the related docs. ...

etwa 2 Jahre vor | 0

Beantwortet
Has anyone done a project with the Texas Instruments TMDSSOLARUINVKIT "Solar Micro Inverter Development Kit" module?
Hi @Andres Lopez, Here the issue is that the Solar Invereter example was created by R2018b and you are using an earlier versi...

fast 4 Jahre vor | 2

Beantwortet
How to build op amp
Hi Khald, Do you have access to Simscape library? You can find the built in block in Simscape library. Best Mohsen

mehr als 4 Jahre vor | 0

Beantwortet
q- d- currents of PMSM drive in Delta configuration
Hi Tom, Could you please tell me if these numbers are the exact values you observe? If not could you please provide the exact...

mehr als 4 Jahre vor | 1

| akzeptiert

Beantwortet
how to connect sum block in Simulink to both ideal switches
This ideal switch belongs to the Specialized Power Systems library. Terminals 1 and 2 cannot be connected to the signal ports. Y...

mehr als 4 Jahre vor | 0

| akzeptiert

Beantwortet
AC/DC Three-Level PWM Converter
The reason is that the topology is not physically able to follow the negative reference. The load consists of two parallel resis...

mehr als 4 Jahre vor | 0

Beantwortet
Embedded Matlab function for Microcontroller modelling with PWM
Hi Eleni.T, The correct answer to this question really depends on your final design. What paramters are being controlled and wh...

mehr als 4 Jahre vor | 0

| akzeptiert