# SM AC9C

Discrete-time or continuous-time synchronous machine AC9C excitation system including an automatic voltage regulator and an exciter

*Since R2023a*

**Libraries:**

Simscape /
Electrical /
Control /
SM Control

## Description

The SM AC9C block implements a synchronous machine type AC9C excitation system model in conformance with Std IEEE 421.5-2016 [1].

Use this block to model the control and regulation of the field voltage of a synchronous machine that operates as a generator using an AC rotating exciter.

Switch between continuous and discrete implementations of the block by using the
**Sample time (-1 for inherited)** parameter. To configure the
integrator for continuous time, set the **Sample time (-1 for
inherited)** parameter to `0`

. To configure the integrator
for discrete time, set the **Sample time (-1 for inherited)** parameter
to a positive scalar. To inherit the sample time from an upstream block, set the
**Sample time (-1 for inherited)** parameter to
`-1`

.

The SM AC9C block comprises five major components:

The Current Compensator component modifies the measured terminal voltage as a function of the terminal current.

The Voltage Measurement Transducer component simulates the dynamics of a terminal voltage transducer using a low-pass filter.

The Excitation Control Elements component compares the voltage transducer output with a terminal voltage reference to produce a voltage error value. The component then passes this value through a voltage regulator to produce the exciter field voltage.

The AC Rotating Exciter component models the AC rotating exciter, which produces a field voltage that is applied to the controlled synchronous machine. The block also feeds the exciter field current (

*V*) back to the excitation system._{FE}The Power Source component models the dependency of the power source for the controlled rectifier from the terminal voltage.

This diagram shows the structure of the AC9C excitation system model:

In the diagram:

*V*and_{T}*I*are the measured terminal voltage and current of the synchronous machine, respectively._{T}*V*is the current-compensated terminal voltage._{C1}*V*is the filtered, current-compensated terminal voltage._{C}*V*is the reference terminal voltage._{REF}*V*is the power system stabilizer voltage._{S}*SW*is the power source switch that you specify for the controlled rectifier._{1}*V*is the exciter field voltage._{B}*E*and_{FE}*V*are the exciter field voltage and current, respectively._{FE}*E*and_{FD}*I*are the field voltage and current, respectively._{FD}

### Current Compensator and Voltage Measurement Transducer

The block models the current compensator by using this equation:

$${V}_{C1}={V}_{T}+{I}_{T}\sqrt{{R}_{C}^{2}+{X}_{C}^{2}},$$

where:

*R*is the load compensation resistance._{C}*X*is the load compensation reactance._{C}

The block implements the voltage measurement transducer as a Low-Pass
Filter block with the time constant
*T _{R}*. Refer to the documentation for the
Low-Pass Filter block for information about the exact discrete and continuous
implementations.

### Excitation Control Elements

This diagram shows the structure of the excitation control elements:

In the diagram:

The Summation Point Logic subsystem models the summation point input location for the overexcitation limiter (OEL), underexcitation limiter (UEL), and stator current limiter (SCL). For more information about using limiters with this block, see Field Current Limiters.

The PID subsystem models a PID controller that functions as a control structure for the automatic voltage regulator. The minimum and maximum anti windup saturation limits for the block are

*V*and_{PIDmin}*V*, respectively._{PIDmax}The Take-over Logic subsystem models the take-over point input location for the OEL, UEL, SCL and PSS voltages. For more information about using limiters with this block, see Field Current Limiters.

The PI_R subsystem models a PI controller that functions as a control structure for the field current regulator. The minimum and maximum anti windup saturation limits for the block are

*V*and_{Amin}*V*, respectively._{Amax}The top Low-Pass Filter block models the major dynamics of the controlled rectified bridge.

*K*is the controlled rectifier bridge equivalent gain and_{A}*T*is the major time constant of the controlled rectifier bridge. The minimum and maximum anti windup saturation limits for the block are_{A}*V*and_{Rmin}*V*, respectively._{Rmax}The bottom Low-Pass Filter block models the rate feedback path for the stabilization of the excitation system.

*K*and_{F}*T*are the gain and time constants of this system, respectively. See the documentation for the Low-Pass Filter block for information about the discrete and continuous implementations._{F}The Power state logic subsystem supports the selection of the power stage type, which can be a thyristor or a chopper converter. If you set the

**Power stage type selector, S_CT**parameter to`Thyristor bridge`

, it represents a thyristor converter. If you set the**Power stage type selector, S_CT**parameter to`Chopper converter`

, it represents a chopper converter. The subsystem sums the voltage regulator command signal*V*to the exciter field voltage_{R}*V*. For more information about the logical switch for the power source of the controlled rectifier and about the power state logic subsystem, see Power Source and Power State Logic._{B}

### Field Current Limiters

You can use different types of field current limiter to modify the output of the voltage regulator under unsafe operating conditions:

Use an overexcitation limiter to prevent overheating of the field winding due to excessive field current demand.

Use an underexcitation limiter to boost field excitation when it is too low, which risks desynchronization.

Use a stator current limiter to prevent overheating of the stator windings due to excessive current.

Attach the output of any of these limiters at one of these points:

Summation point — Use the limiter as part of the automatic voltage regulator (AVR) feedback loop.

Take-over point — Override the usual behavior of the AVR.

If you are using the stator current limiter at the summation point,
use the input *V _{SCLsum}*. If you are using
the stator current limiter at the take-over point, use the overexcitation input

*V*, and the underexcitation input

_{OELscl}*V*.

_{UELscl}### AC Rotating Exciter

This diagram shows the structure of the AC rotating exciter:

In the diagram:

The exciter field current

*V*is the sum of three signals:_{FE}The nonlinear function

*V*models the saturation of the exciter output voltage._{x}The proportional term

*K*models the linear relationship between the exciter output voltage and the exciter field current._{E}The subsystem models the demagnetizing effect of the load current on the exciter output voltage using the demagnetization constant

*K*in the feedback loop._{D}

The Integrator with variable limits subsystem integrates the difference between

*E*and_{FE}*V*to generate the exciter alternator output voltage_{FE}*V*._{E}*T*is the time constant for this process._{E}The nonlinear function

*F*models the exciter output voltage drop from the rectifier regulation. This function depends on the constant_{EX}*K*, which itself is a function of commutating reactance._{C}The parameters

*V*and_{Emin}*V*model the lower and upper limits of the rotating exciter._{FEmax}

### Power Source and Power State Logic

You can use different power source representations for the controlled rectifier by setting
the **Power source selector SW1** parameter value. To derive the
power source for the controlled rectifier from the terminal voltage, set the
**Power source selector SW1** parameter to
```
Position A: power source derived from terminal
voltage
```

. To specify that the power source is independent of the
terminal voltage, set the **Power source selector SW1** parameter
to ```
Position B: power source independent from the terminal
conditions
```

.

The Power state logic subsystem supports the selection of the power stage type, which can
be a thyristor or a chopper converter. If you set the **Power stage type
selector, S_CT** parameter to ```
Thyristor
bridge
```

, the Power state logic subsystem represents a thyristor
converter. If you set the **Power stage type selector, S_CT**
parameter to `Chopper converter`

, the Power state logic
subsystem represents a chopper converter. The value of the voltage regulator command
signal *V _{R}* depends on the

**Voltage limit, V_lim1 (pu)**and

**Voltage limit, V_lim2 (pu)**parameters and on the

*V*,

_{CT}*V*, and

_{FW}*V*signals according to this logic:

_{AVR}if S_CT ~= 0 % Thyristor bridge V_R = V_CT else % Chopper converter if V_AVR > V_lim1 V_R = C_T else if V_AVR > V_lim2 V_R = 0 else V_R = -V_FW end end end

## Ports

### Input

### Output

## Parameters

## References

[1] IEEE Std 421.5-2016 (Revision of
IEEE Std 421.5-2005). "*IEEE Recommended Practice for Excitation System Models
for Power System Stability Studies.*" Piscataway, NJ: IEEE,
2016.

## Extended Capabilities

## Version History

**Introduced in R2023a**