Beantwortet
Error connecting Arduino hardware to MATLAB R2018b
Have you tried uninstalling and reinstalling the support package? When installing these support packages if additional terminal ...

etwa 5 Jahre vor | 0

Beantwortet
"measure temperature from i2c device using arduino hardware".
Can you try with other arduino boards or other sensors? That code works for me on the Arduino and TMP102 sensor.

etwa 5 Jahre vor | 0

Beantwortet
"measure temperature from i2c device using arduino hardware".
What is the Arduino board using and does your hardware setup look similar to the one shown here - https://www.mathworks.com/help...

etwa 5 Jahre vor | 0

Beantwortet
The problem of delay in contact with Ardiono
When you attempt to open a connection with Arduino, MATLAB downloads an Arduino sketch to the hardware and this is the reason it...

etwa 5 Jahre vor | 0

Beantwortet
matlab function for arduino
I think you are better off using the Simulink workflow to perform controls and not use the MATLAB Support package for Arduino fu...

etwa 5 Jahre vor | 0

Beantwortet
matlab function for arduino
Based on the error it looks like you are attempting to use MATLAB Function block within a Simulink Model. In this approach, you ...

etwa 5 Jahre vor | 0

Beantwortet
Recording values from I2C sensors
If you use MATLAB Support Package for Arduino, there is readRegister function to read data in - https://www.mathworks.com/help/s...

etwa 5 Jahre vor | 0

Beantwortet
Can't connect Arduino Uno (Genuino) to Matlab R2016a
Try putting the device in bootloader mode, by double presssing the RESET button.

etwa 5 Jahre vor | 0

Beantwortet
How to read COM port caption
seriallist command is used to detect additions to the COM port #s (only available starting R2017a). However in this technique yo...

etwa 5 Jahre vor | 1

Beantwortet
How I can read data from VL53L0X in simulink?
I would recommend creating your own block using the techniques described in this video - https://www.youtube.com/watch?v=qoj8Pa2...

etwa 5 Jahre vor | 1

| akzeptiert

Beantwortet
Raspberry pi board connecting to matlab
So I am assuming this is right after MATLAB Support package for Raspberry Pi Setup. If it fails, I usually try the following - ...

etwa 5 Jahre vor | 0

Beantwortet
Arduino Temperature Sensor with buttons
If you need your code to be deployed to the Arduino and work independent of PC, then use Simulink Support Package for Arduino. I...

etwa 5 Jahre vor | 0

Beantwortet
Servo Library with Simulink and Arduino
This video has some relevant items - https://www.youtube.com/watch?v=qoj8Pa2wi0A but needs to be adapted for your case

etwa 5 Jahre vor | 0

Beantwortet
No connection to mkr1000 board.
Try putting the Arduino in bootloader mode before downloading the Simulink model and also make Simulink automatically set COM po...

etwa 5 Jahre vor | 0

Beantwortet
How do i plot ECG sensor data from arduino to ECG graph using matlab?
Here are my thoughts on this topic and unfortunately I am not a subject matter expert on this. https://www.mathworks.com/video...

etwa 5 Jahre vor | 0

Beantwortet
How do i plot ECG sensor data from arduino to ECG graph using matlab?
You can search through the MATLAB File Exchange to see if there are pre-existing libraries that you can use. If not, you will ha...

etwa 5 Jahre vor | 0

Beantwortet
I want to add two pulse generator in simulink and dump it into arduino uno...the result i am getting is change in the frequency at arduino output what i have set in pulse generator?
Here is what I think is going on - the model is overrunning itself as the sample time for model is small (0.000625 or 1600 Hz). ...

etwa 5 Jahre vor | 0

Beantwortet
I want to add two pulse generator in simulink and dump it into arduino uno...the result i am getting is change in the frequency at arduino output what i have set in pulse generator?
Here is what I would recommend - 1) Create a new Simulation only model and put two pulse generators both with a sampling perio...

etwa 5 Jahre vor | 1

Beantwortet
I want to add two pulse generator in simulink and dump it into arduino uno...the result i am getting is change in the frequency at arduino output what i have set in pulse generator?
The correct way would be to have one pulse generator with period 0.02 seconds and appropriate Pulse Width. Adding two blocks doe...

etwa 5 Jahre vor | 0

| akzeptiert

Beantwortet
HC-SR04 library listArduinoLibraries is not showing it.
Have you tried using this? - https://www.mathworks.com/matlabcentral/fileexchange/57898-hc-sr04-add-on-library-for-arduino Ple...

etwa 5 Jahre vor | 0

Beantwortet
Install Arduino uno offline
Does this help - https://www.mathworks.com/matlabcentral/answers/293235-how-do-i-download-hardware-support-packages-and-optional...

etwa 5 Jahre vor | 0

Beantwortet
I need help about my arduino LED project
There is a warning/error on MATLAB - that MATLAB experienced a low-level ... I suspect that has something to do with the Sco...

etwa 5 Jahre vor | 0

Beantwortet
how read acceleration data for BNO055
This sensor is supported in the Simulink support package for Arduino - https://www.mathworks.com/help/supportpkg/arduino/ref/bno...

etwa 5 Jahre vor | 1

Beantwortet
Can anyone help me please ?
If you tried those instructions and are getting the same error, try the Set host COM port option to Automatically in the same pa...

etwa 5 Jahre vor | 0

Beantwortet
How to make a step function from 2 volts to 2.5 volts in matlab using Arduino? (without Simulink and step matlab function itself)
What if you changed your code to the following - clc clear all a = arduino; writePWMVoltage(a,'D5',2); for k = 1:1000 ...

etwa 5 Jahre vor | 1

| akzeptiert

Beantwortet
Can't get my Matlab and Simulink license
You can check if that process went through correctly to create your license or not, by going to your accounts page. 1) Log i...

etwa 5 Jahre vor | 2

| akzeptiert

Beantwortet
How to filter ECG signal from an Arduino in real-time using Simulink?
https://www.mathworks.com/videos/how-to-build-a-heart-rate-detector-using-arduino-and-matlab-1520412607264.html This example...

etwa 5 Jahre vor | 1

Beantwortet
Are Dutch Secondary School eligible for student licences?
https://www.mathworks.com/academia/highschool.html This license might be a better fit for primary and secondary schools as the...

etwa 5 Jahre vor | 0

Beantwortet
analog Encoder in Matlab and arduino
Just go ahead and connect the encoder outs to digital pins that you have access to. Then use rotaryEncoder function on those dig...

etwa 5 Jahre vor | 2

| akzeptiert

Beantwortet
analog Encoder in Matlab and arduino
The rotaryEncoder function is only going to work with quadrature encoders as noted in the documentation. It seems to me like th...

etwa 5 Jahre vor | 1

Mehr laden