Beantwortet
How does a retargeted model know about the subsystem on the FPGA?
Hi Harry, I am going to assume that you are using the <https://www.mathworks.com/help/supportpkg/xilinxzynqbasedradio/ug/fpga...

etwa 7 Jahre vor | 1

| akzeptiert

Beantwortet
Zynq SDR Receiver Block outputs data regardless of hardware state/cannot detect 802.11 beacons.
Hi Harry, This example will only receive 802.11b standard waveforms. I believe many routers do not transmit that beacon by de...

etwa 7 Jahre vor | 2

| akzeptiert

Beantwortet
HW/SW Co-design QPSK Transceiver example - Will only load Tx channel onto ADRV9361?
Hi Harry, You have hit a bug in our information returned here I'm afraid. If you target both transmitter and receiver, it wil...

etwa 7 Jahre vor | 1

| akzeptiert

Beantwortet
How can I enable my E310 to receive over-the-air ADS-B Signals?
Hi Ben, To disable the transmitter, right click on the transmitter block and select "Comment Out". Do the same for the consta...

mehr als 7 Jahre vor | 0

Beantwortet
Communications System Toolbox Support for Xilinx Zynq-based SDR - is the Xilinx ZC702 board supported?
Hi Kevin, Unfortunately the ZC702 is not on our list of supported devices. The ZC706 and ZedBoard both have different hardwar...

mehr als 7 Jahre vor | 0

Beantwortet
Ettus E310 setup issues. Incompatible Hardware.
Hi Will, Another customer has experienced the same issue, and by comparing their installation with yours, we were able to fig...

mehr als 7 Jahre vor | 0

Beantwortet
How to use external refernce clock with PicoZed SDR and MATLAB
Hi Yannay, Unfortunately at this point there is no easy way to configure the external clock using our tools. If you require f...

fast 8 Jahre vor | 0

Beantwortet
is it possible to create a stand alone system using simulink libraries?
Hi Samer, There are a couple of methods you can use to send or receive data with MATLAB disconnected. Firstly, the <https:...

fast 8 Jahre vor | 1

| akzeptiert

Beantwortet
Offline Install of Communications System Toolbox Support Package for Xilinx Zynq-Based Radio
Hi Seth, Please could you contact <https://uk.mathworks.com/support/contact_us/ technical support> for this question? Than...

fast 8 Jahre vor | 0

Beantwortet
Difference between SDR transmitter and tx.transmitrepeat function
Hi Angie, When you use the Simulink block, you are attempting to stream data from Simulink across the Ethernet link to the bo...

etwa 8 Jahre vor | 0

| akzeptiert

Beantwortet
Issue with generated library blocks
Hi Faris, You are using the support package in two different ways in your description above. In the second case, you are ...

etwa 8 Jahre vor | 0

| akzeptiert

Beantwortet
[Zynq ad9361 fmscomms2] Frame Size increase
Hello, yes you can change the data packet size that is sent to the transmitter. In the example, the software running on the ARM ...

etwa 8 Jahre vor | 1

| akzeptiert

Beantwortet
[zynq communication toolbox] how to specify the sampling rate
Hi Jeffrey, The Baseband sample rate parameter on the SDR transmitter block is the rate at which the sample will be sent by t...

mehr als 8 Jahre vor | 0

Beantwortet
Zynq SDR: sustained transfer of data from picozed?
Hi, The N210 and PicoZed SDR are based on different infrastructure, so may behave in different ways. For the PicoZed SDR, the...

mehr als 8 Jahre vor | 0

Beantwortet
HW/SW Co-design full deployment using ZedBoard issues
Hi John, My apologies for the late response. It's good to hear you've already come as far as you have. Some responses to your...

mehr als 8 Jahre vor | 2

Beantwortet
ZedBoard connection problems after loading a custom bitstream
Hi Johannes, Apologies for the delayed response. It is unlikely to be the anti-virus or firewall behaviour. It's hard to tell...

mehr als 8 Jahre vor | 0

Beantwortet
How to specify sample rates for Xilinx Zynq-Based Radio?
Hi Johannes, Apologies for the delay in responding. Unfortunately you are hitting a limitation in the FPGA-only targeting wor...

mehr als 8 Jahre vor | 0

Beantwortet
IP Core genration in hdl coder for Zedboard FMCOMMS2 Channel Mapping
Hi Pooria, I'm afraid the the targeting workflow is only supported from Simulink. You could try including your m-code in a <...

mehr als 8 Jahre vor | 0

| akzeptiert

Beantwortet
IP Core genration in hdl coder for Zedboard FMCOMMS2 Channel Mapping
Hi Pooria, Thanks for your question. I need some more information on what you are trying to do to be able to answer your quer...

mehr als 8 Jahre vor | 0

Beantwortet
Why Mathworks SDR Firmware is unable to read FRU/EEPROM information on 'ZedBoard and FMCOMMS2/3/4'
Hi, In the MathWorks SDR firmware, the FRU information is read only to identify the RF card to set the correct maximum number...

etwa 9 Jahre vor | 0

| akzeptiert

Beantwortet
Support and Limitations using Mathworks Software w/ Avnet PicoZedSDR
Hi Richard, The <http://www.mathworks.com/hardware-support/zynq-sdr.html Zynq Radio HSP> will let you stream data into and ou...

fast 10 Jahre vor | 1

| akzeptiert