Daniel Gelman
University of Western Ontario - Robarts Research Institute
Followers: 0 Following: 0
MESc Biomedical Engineering student at Robarts Research Institute. Professional Interests: Image-Guided Interventions
Statistiken
RANG
6.091
of 290.067
REPUTATION
7
ANTWORTZUSTIMMUNG
0.0%
ERHALTENE STIMMEN
7
RANG
of 19.635
REPUTATION
N/A
DURCHSCHNITTLICHE BEWERTUNG
0.00
BEITRÄGE
0 Dateien
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANG
of 144.471
BEITRÄGE
0 Probleme
0 Lösungen
PUNKTESTAND
0
ANZAHL DER ABZEICHEN
0
BEITRÄGE
0 Beiträge
BEITRÄGE
0 Öffentlich Kanäle
DURCHSCHNITTLICHE BEWERTUNG
BEITRÄGE
0 Highlights
DURCHSCHNITTLICHE ANZAHL DER LIKES
Feeds
Frage
XCP master internal error, serial receive, Arduino external mode
I have a very simple model I am trying to deploy onto an Arduino Due target hardware in external mode (Monitor & Tune). Just try...
fast 3 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Running Simulink PID model with external reset and output saturation on Arduino target hardware.
On an Arduino, I've implemented an s-function to receive variables from a 2nd microcontroller via Serial. The model, which can...
mehr als 3 Jahre vor | 0 Antworten | 0
0
AntwortenFrage
Simulink & Arduino: Transmit Serial strings
I am trying to transmit serial data out of an Arduino in Simulink, see model below. I am getting prompted with The 'MATLABS...
mehr als 3 Jahre vor | 1 Antwort | 1
1
AntwortFrage
Simulink/Arduino: serial receive byte stream
Hello, I am using Simulink to receive serial data via Arduino, which is receiving three bytes (unit8) of data from a 2nd microc...
mehr als 3 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Simulink, Arduino as slave-receiver in I2C
I have 2 Arduinos: One Arduino MEGA is master-writer in an I2C bus, providing data at ~20 Hz. The other is an Arduino DUE in a...
mehr als 3 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Could not connect to XCP slave: XCP Master internal error: Busy(0) or no timeout(2) for 255
Hello, I've used the S-Function Builder to use an Arduino library in Simulink. Specifically, I am trying to use the AccelSteppe...
etwa 4 Jahre vor | 4 Antworten | 6
4
AntwortenFrage
Sorted Execution Order, Initial Conditions, PID
Below is a closed-loop system of plant Gp(z) with unity gain. I also enabled to display the sorted execution order. <</matlab...
mehr als 6 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Shaping PID to achieve load disturbance performance
I am using the PID Tuner for the PID Controller Block in Simulink. I am particularly interested in the output disturbance BODE p...
mehr als 6 Jahre vor | 1 Antwort | 0
1
AntwortFrage
ss2tf() Acting Oddly
I am constructing a few transfer functions and I believe this the output is very wrong. I am not expecting the numerator and den...
mehr als 7 Jahre vor | 1 Antwort | 0
1
AntwortIdentical models in MATLAB and Simulink do not match each other
[Answered] Always be aware of significant figures. Even 0.0001 can make a difference in differential equations.
mehr als 7 Jahre vor | 0
Frage
How to Initialize a Discrete-Time Model?
Hello, I have the following discrete-time model. num = [0.02884 -0.02844]; den = [1 -1.7298 0.7337]; H = tf(num,...
mehr als 7 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Identical models in MATLAB and Simulink do not match each other
I am noticing that discrete-time models I am using in Simulink do not match the same response in the Matlab environment. For ...
mehr als 7 Jahre vor | 1 Antwort | 0
1
AntwortFrage
New to FFT - is my result valid?
Hello, I am revisiting Matlab FFT after years of not practicing. I have a signal in which I removed the DC component and plot...
mehr als 9 Jahre vor | 1 Antwort | 0
1
AntwortFrage
Raspberry Pi Simulink Communication Error
Hello, I am fairly new to Simulink and I am trying to incorporate a stand alone application running the model on a Raspberry ...
fast 11 Jahre vor | 1 Antwort | 0